commit 765675379b6253b6901563e649a2f87d28ada3ff
Author: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Date: Wed Apr 29 16:31:35 2020 +0200
Linux 4.19.119
commit 215d1f3928713d6eaec67244bcda72105b898000
Author: Christian Borntraeger <borntraeger@de.ibm.com>
Date: Wed Apr 15 15:21:01 2020 +0200
s390/mm: fix page table upgrade vs 2ndary address mode accesses
commit 316ec154810960052d4586b634156c54d0778f74 upstream.
A page table upgrade in a kernel section that uses secondary address
mode will mess up the kernel instructions as follows:
Consider the following scenario: two threads are sharing memory.
On CPU1 thread 1 does e.g. strnlen_user(). That gets to
old_fs = enable_sacf_uaccess();
len = strnlen_user_srst(src, size);
and
" la %2,0(%1)\n"
" la %3,0(%0,%1)\n"
" slgr %0,%0\n"
" sacf 256\n"
"0: srst %3,%2\n"
in strnlen_user_srst(). At that point we are in secondary space mode,
control register 1 points to kernel page table and instruction fetching
happens via c1, rather than usual c13. Interrupts are not disabled, for
obvious reasons.
On CPU2 thread 2 does MAP_FIXED mmap(), forcing the upgrade of page table
from 3-level to e.g. 4-level one. We'd allocated new top-level table,
set it up and now we hit this:
notify = 1;
spin_unlock_bh(&mm->page_table_lock);
}
if (notify)
on_each_cpu(__crst_table_upgrade, mm, 0);
OK, we need to actually change over to use of new page table and we
need that to happen in all threads that are currently running. Which
happens to include the thread 1. IPI is delivered and we have
static void __crst_table_upgrade(void *arg)
{
struct mm_struct *mm = arg;
if (current->active_mm == mm)
set_user_asce(mm);
__tlb_flush_local();
}
run on CPU1. That does
static inline void set_user_asce(struct mm_struct *mm)
{
S390_lowcore.user_asce = mm->context.asce;
OK, user page table address updated...
__ctl_load(S390_lowcore.user_asce, 1, 1);
... and control register 1 set to it.
clear_cpu_flag(CIF_ASCE_PRIMARY);
}
IPI is run in home space mode, so it's fine - insns are fetched
using c13, which always points to kernel page table. But as soon
as we return from the interrupt, previous PSW is restored, putting
CPU1 back into secondary space mode, at which point we no longer
get the kernel instructions from the kernel mapping.
The fix is to only fixup the control registers that are currently in use
for user processes during the page table update. We must also disable
interrupts in enable_sacf_uaccess to synchronize the cr and
thread.mm_segment updates against the on_each-cpu.
Fixes: 0aaba41b58bc ("s390: remove all code using the access register mode")
Cc: stable@vger.kernel.org # 4.15+
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
References: CVE-2020-11884
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fb102dd99f40ad98a1d55b30c30ae34e7a19cdd
Author: kaixuxia <xiakaixu1987@gmail.com>
Date: Tue Sep 3 21:06:50 2019 -0700
xfs: Fix deadlock between AGI and AGF with RENAME_WHITEOUT
commit bc56ad8c74b8588685c2875de0df8ab6974828ef upstream.
When performing rename operation with RENAME_WHITEOUT flag, we will
hold AGF lock to allocate or free extents in manipulating the dirents
firstly, and then doing the xfs_iunlink_remove() call last to hold
AGI lock to modify the tmpfile info, so we the lock order AGI->AGF.
The big problem here is that we have an ordering constraint on AGF
and AGI locking - inode allocation locks the AGI, then can allocate
a new extent for new inodes, locking the AGF after the AGI. Hence
the ordering that is imposed by other parts of the code is AGI before
AGF. So we get an ABBA deadlock between the AGI and AGF here.
Process A:
Call trace:
? __schedule+0x2bd/0x620
schedule+0x33/0x90
schedule_timeout+0x17d/0x290
__down_common+0xef/0x125
? xfs_buf_find+0x215/0x6c0 [xfs]
down+0x3b/0x50
xfs_buf_lock+0x34/0xf0 [xfs]
xfs_buf_find+0x215/0x6c0 [xfs]
xfs_buf_get_map+0x37/0x230 [xfs]
xfs_buf_read_map+0x29/0x190 [xfs]
xfs_trans_read_buf_map+0x13d/0x520 [xfs]
xfs_read_agf+0xa6/0x180 [xfs]
? schedule_timeout+0x17d/0x290
xfs_alloc_read_agf+0x52/0x1f0 [xfs]
xfs_alloc_fix_freelist+0x432/0x590 [xfs]
? down+0x3b/0x50
? xfs_buf_lock+0x34/0xf0 [xfs]
? xfs_buf_find+0x215/0x6c0 [xfs]
xfs_alloc_vextent+0x301/0x6c0 [xfs]
xfs_ialloc_ag_alloc+0x182/0x700 [xfs]
? _xfs_trans_bjoin+0x72/0xf0 [xfs]
xfs_dialloc+0x116/0x290 [xfs]
xfs_ialloc+0x6d/0x5e0 [xfs]
? xfs_log_reserve+0x165/0x280 [xfs]
xfs_dir_ialloc+0x8c/0x240 [xfs]
xfs_create+0x35a/0x610 [xfs]
xfs_generic_create+0x1f1/0x2f0 [xfs]
...
Process B:
Call trace:
? __schedule+0x2bd/0x620
? xfs_bmapi_allocate+0x245/0x380 [xfs]
schedule+0x33/0x90
schedule_timeout+0x17d/0x290
? xfs_buf_find+0x1fd/0x6c0 [xfs]
__down_common+0xef/0x125
? xfs_buf_get_map+0x37/0x230 [xfs]
? xfs_buf_find+0x215/0x6c0 [xfs]
down+0x3b/0x50
xfs_buf_lock+0x34/0xf0 [xfs]
xfs_buf_find+0x215/0x6c0 [xfs]
xfs_buf_get_map+0x37/0x230 [xfs]
xfs_buf_read_map+0x29/0x190 [xfs]
xfs_trans_read_buf_map+0x13d/0x520 [xfs]
xfs_read_agi+0xa8/0x160 [xfs]
xfs_iunlink_remove+0x6f/0x2a0 [xfs]
? current_time+0x46/0x80
? xfs_trans_ichgtime+0x39/0xb0 [xfs]
xfs_rename+0x57a/0xae0 [xfs]
xfs_vn_rename+0xe4/0x150 [xfs]
...
In this patch we move the xfs_iunlink_remove() call to
before acquiring the AGF lock to preserve correct AGI/AGF locking
order.
[Minor massage required due to upstream change making xfs_bumplink() a
void function where as in the 4.19.y tree the return value is checked,
even though it is always zero. Only change was to the last code block
removed by the patch. Functionally equivalent to upstream.]
Signed-off-by: kaixuxia <kaixuxia@tencent.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Suraj Jitindar Singh <surajjs@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d407f7dc0662ec2d8c5f79d79786144d3340e761
Author: Kazuhiro Fujita <kazuhiro.fujita.jg@renesas.com>
Date: Fri Mar 27 18:17:28 2020 +0000
serial: sh-sci: Make sure status register SCxSR is read in correct sequence
commit 3dc4db3662366306e54ddcbda4804acb1258e4ba upstream.
For SCIF and HSCIF interfaces the SCxSR register holds the status of
data that is to be read next from SCxRDR register, But where as for
SCIFA and SCIFB interfaces SCxSR register holds status of data that is
previously read from SCxRDR register.
This patch makes sure the status register is read depending on the port
types so that errors are caught accordingly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kazuhiro Fujita <kazuhiro.fujita.jg@renesas.com>
Signed-off-by: Hao Bui <hao.bui.yg@renesas.com>
Signed-off-by: KAZUMI HARADA <kazumi.harada.rh@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1585333048-31828-1-git-send-email-kazuhiro.fujita.jg@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3ee95dedd88ed3fcd4647e4a8e265acaf27b2f0
Author: Mathias Nyman <mathias.nyman@linux.intel.com>
Date: Tue Apr 21 17:08:21 2020 +0300
xhci: prevent bus suspend if a roothub port detected a over-current condition
commit e9fb08d617bfae5471d902112667d0eeb9dee3c4 upstream.
Suspending the bus and host controller while a port is in a over-current
condition may halt the host.
Also keep the roothub running if over-current is active.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0a0ebfed4b2b218f7b1d357fba8a0942c14b333
Author: Udipto Goswami <ugoswami@codeaurora.org>
Date: Thu Apr 2 10:15:21 2020 +0530
usb: f_fs: Clear OS Extended descriptor counts to zero in ffs_data_reset()
commit 1c2e54fbf1da5e5445a0ab132c862b02ccd8d230 upstream.
For userspace functions using OS Descriptors, if a function also supplies
Extended Property descriptors currently the counts and lengths stored in
the ms_os_descs_ext_prop_{count,name_len,data_len} variables are not
getting reset to 0 during an unbind or when the epfiles are closed. If
the same function is re-bound and the descriptors are re-written, this
results in those count/length variables to monotonically increase
causing the VLA allocation in _ffs_func_bind() to grow larger and larger
at each bind/unbind cycle and eventually fail to allocate.
Fix this by clearing the ms_os_descs_ext_prop count & lengths to 0 in
ffs_data_reset().
Fixes: f0175ab51993 ("usb: gadget: f_fs: OS descriptors support")
Cc: stable@vger.kernel.org
Signed-off-by: Udipto Goswami <ugoswami@codeaurora.org>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Link: https://lore.kernel.org/r/20200402044521.9312-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbee0a82061a9d1623dea35c34bc79c5e9b7daa1
Author: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Date: Tue Mar 31 01:40:35 2020 -0700
usb: dwc3: gadget: Fix request completion check
commit 49e0590e3a60e75b493e5df879e216e5073c7663 upstream.
A request may not be completed because not all the TRBs are prepared for
it. This happens when we run out of available TRBs. When some TRBs are
completed, the driver needs to prepare the rest of the TRBs for the
request. The check dwc3_gadget_ep_request_completed() shouldn't be
checking the amount of data received but rather the number of pending
TRBs. Revise this request completion check.
Cc: stable@vger.kernel.org
Fixes: e0c42ce590fe ("usb: dwc3: gadget: simplify IOC handling")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e076da135b81df39e95a10a2360eb49c868ae68f
Author: Oliver Neukum <oneukum@suse.com>
Date: Wed Apr 15 16:17:50 2020 +0200
UAS: fix deadlock in error handling and PM flushing work
commit f6cc6093a729ede1ff5658b493237c42b82ba107 upstream.
A SCSI error handler and block runtime PM must not allocate
memory with GFP_KERNEL. Furthermore they must not wait for
tasks allocating memory with GFP_KERNEL.
That means that they cannot share a workqueue with arbitrary tasks.
Fix this for UAS using a private workqueue.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: f9dc024a2da1f ("uas: pre_reset and suspend: Fix a few races")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200415141750.811-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ca6a4d89872d6c1abb41ded2aa139b703d67ab2
Author: Oliver Neukum <oneukum@suse.com>
Date: Wed Apr 15 16:17:49 2020 +0200
UAS: no use logging any details in case of ENODEV
commit 5963dec98dc52d52476390485f07a29c30c6a582 upstream.
Once a device is gone, the internal state does not matter anymore.
There is no need to spam the logs.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 326349f824619 ("uas: add dead request list")
Link: https://lore.kernel.org/r/20200415141750.811-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 465f0c0b5306bcae604216dd4363d003554f886c
Author: Oliver Neukum <oneukum@suse.com>
Date: Wed Apr 15 17:13:58 2020 +0200
cdc-acm: introduce a cool down
commit a4e7279cd1d19f48f0af2a10ed020febaa9ac092 upstream.
Immediate submission in case of a babbling device can lead
to a busy loop. Introducing a delayed work.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Jonas Karlsson <jonas.karlsson@actia.se>
Link: https://lore.kernel.org/r/20200415151358.32664-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 681c2486f9f9a56dc8e851245838b001ad326d35
Author: Oliver Neukum <oneukum@suse.com>
Date: Wed Apr 15 17:13:57 2020 +0200
cdc-acm: close race betrween suspend() and acm_softint
commit 0afccd7601514c4b83d8cc58c740089cc447051d upstream.
Suspend increments a counter, then kills the URBs,
then kills the scheduled work. The scheduled work, however,
may reschedule the URBs. Fix this by having the work
check the counter.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Jonas Karlsson <jonas.karlsson@actia.se>
Link: https://lore.kernel.org/r/20200415151358.32664-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90fbd0773ba25f99c144e5042bddbbd70a599db1
Author: Malcolm Priestley <tvboxspy@gmail.com>
Date: Tue Apr 14 11:39:23 2020 +0100
staging: vt6656: Power save stop wake_up_count wrap around.
commit ea81c3486442f4643fc9825a2bb1b430b829bccd upstream.
conf.listen_interval can sometimes be zero causing wake_up_count
to wrap around up to many beacons too late causing
CTRL-EVENT-BEACON-LOSS as in.
wpa_supplicant[795]: message repeated 45 times: [..CTRL-EVENT-BEACON-LOSS ]
Fixes: 43c93d9bf5e2 ("staging: vt6656: implement power saving code.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/fce47bb5-7ca6-7671-5094-5c6107302f2b@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2179f148b7e6244977e8614229e35a5809e1b758
Author: Malcolm Priestley <tvboxspy@gmail.com>
Date: Sat Apr 18 22:01:49 2020 +0100
staging: vt6656: Fix pairwise key entry save.
commit 0b59f10b1d8fe8d50944f21f5d403df9303095a8 upstream.
The problem is that the group key was saved as VNT_KEY_DEFAULTKEY
was over written by the VNT_KEY_GROUP_ADDRESS index.
mac80211 could not clear the mac_addr in the default key.
The VNT_KEY_DEFAULTKEY is not necesscary so remove it and set as
VNT_KEY_GROUP_ADDRESS.
mac80211 can clear any key using vnt_mac_disable_keyentry.
Fixes: f9ef05ce13e4 ("staging: vt6656: Fix pairwise key for non station modes")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/da2f7e7f-1658-1320-6eee-0f55770ca391@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d60fdefc1b0e0478fb0966ea974ead74b698250f
Author: Malcolm Priestley <tvboxspy@gmail.com>
Date: Sat Apr 18 17:43:24 2020 +0100
staging: vt6656: Fix drivers TBTT timing counter.
commit 09057742af98a39ebffa27fac4f889dc873132de upstream.
The drivers TBTT counter is not synchronized with mac80211 timestamp.
Reorder the functions and use vnt_update_next_tbtt to do the final
synchronize.
Fixes: c15158797df6 ("staging: vt6656: implement TSF counter")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/375d0b25-e8bc-c8f7-9b10-6cc705d486ee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6eb9ad6d64b152fad3d4cc10f2c999145cb970bc
Author: Malcolm Priestley <tvboxspy@gmail.com>
Date: Sat Apr 18 18:37:18 2020 +0100
staging: vt6656: Fix calling conditions of vnt_set_bss_mode
commit 664ba5180234593b4b8517530e8198bf2f7359e2 upstream.
vnt_set_bss_mode needs to be called on all changes to BSS_CHANGED_BASIC_RATES,
BSS_CHANGED_ERP_PREAMBLE and BSS_CHANGED_ERP_SLOT
Remove all other calls and vnt_update_ifs which is called in vnt_set_bss_mode.
Fixes an issue that preamble mode is not being updated correctly.
Fixes: c12603576e06 ("staging: vt6656: Only call vnt_set_bss_mode on basic rates change.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/44110801-6234-50d8-c583-9388f04b486c@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2332a899ad41f74f02f3660590c89fa6f330718a
Author: Malcolm Priestley <tvboxspy@gmail.com>
Date: Sat Apr 18 17:24:50 2020 +0100
staging: vt6656: Don't set RCR_MULTICAST or RCR_BROADCAST by default.
commit 0f8240bfc070033a4823b19883efd3d38c7735cc upstream.
mac80211/users control whether multicast is on or off don't enable it by default.
Fixes an issue when multicast/broadcast is always on allowing other beacons through
in power save.
Fixes: db8f37fa3355 ("staging: vt6656: mac80211 conversion: main_usb add functions...")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Link: https://lore.kernel.org/r/2c24c33d-68c4-f343-bd62-105422418eac@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b91c4171c74e07fc0deeeba79e8a6ffbd052f841
Author: Nicolas Pitre <nico@fluxnic.net>
Date: Sat Mar 28 22:25:11 2020 -0400
vt: don't use kmalloc() for the unicode screen buffer
commit 9a98e7a80f95378c9ee0c644705e3b5aa54745f1 upstream.
Even if the actual screen size is bounded in vc_do_resize(), the unicode
buffer is still a little more than twice the size of the glyph buffer
and may exceed MAX_ORDER down the kmalloc() path. This can be triggered
from user space.
Since there is no point having a physically contiguous buffer here,
let's avoid the above issue as well as reducing pressure on high order
allocations by using vmalloc() instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003282214210.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a03e2be16de48536ca0396813bd0be4f24dfd0a
Author: Nicolas Pitre <nico@fluxnic.net>
Date: Sat Mar 28 17:32:42 2020 -0400
vt: don't hardcode the mem allocation upper bound
commit 2717769e204e83e65b8819c5e2ef3e5b6639b270 upstream.
The code in vc_do_resize() bounds the memory allocation size to avoid
exceeding MAX_ORDER down the kzalloc() call chain and generating a
runtime warning triggerable from user space. However, not only is it
unwise to use a literal value here, but MAX_ORDER may also be
configurable based on CONFIG_FORCE_MAX_ZONEORDER.
Let's use KMALLOC_MAX_SIZE instead.
Note that prior commit bb1107f7c605 ("mm, slab: make sure that
KMALLOC_MAX_SIZE will fit into MAX_ORDER") the KMALLOC_MAX_SIZE value
could not be relied upon.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org> # v4.10+
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003281702410.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a147ff0c5f93749e4eace24582587521cdb3952
Author: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Date: Mon Apr 20 13:44:16 2020 +0800
staging: comedi: Fix comedi_device refcnt leak in comedi_open
commit 332e0e17ad49e084b7db670ef43b5eb59abd9e34 upstream.
comedi_open() invokes comedi_dev_get_from_minor(), which returns a
reference of the COMEDI device to "dev" with increased refcount.
When comedi_open() returns, "dev" becomes invalid, so the refcount
should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
comedi_open(). When "cfp" allocation is failed, the refcnt increased by
comedi_dev_get_from_minor() is not decreased, causing a refcnt leak.
Fix this issue by calling comedi_dev_put() on this error path when "cfp"
allocation is failed.
Fixes: 20f083c07565 ("staging: comedi: prepare support for per-file read and write subdevices")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/1587361459-83622-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 462c96c37bb1a03076cfdc0c22890f974d4277fb
Author: Ian Abbott <abbotti@mev.co.uk>
Date: Mon Apr 6 15:20:15 2020 +0100
staging: comedi: dt2815: fix writing hi byte of analog output
commit ed87d33ddbcd9a1c3b5ae87995da34e6f51a862c upstream.
The DT2815 analog output command is 16 bits wide, consisting of the
12-bit sample value in bits 15 to 4, the channel number in bits 3 to 1,
and a voltage or current selector in bit 0. Both bytes of the 16-bit
command need to be written in turn to a single 8-bit data register.
However, the driver currently only writes the low 8-bits. It is broken
and appears to have always been broken.
Electronic copies of the DT2815 User's Manual seem impossible to find
online, but looking at the source code, a best guess for the sequence
the driver intended to use to write the analog output command is as
follows:
1. Wait for the status register to read 0x00.
2. Write the low byte of the command to the data register.
3. Wait for the status register to read 0x80.
4. Write the high byte of the command to the data register.
Step 4 is missing from the driver. Add step 4 to (hopefully) fix the
driver.
Also add a "FIXME" comment about setting bit 0 of the low byte of the
command. Supposedly, it is used to choose between voltage output and
current output, but the current driver always sets it to 1.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200406142015.126982-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eeab3452c8470713eec8ee27a7e0cbeba6c9b6d3
Author: Chris Packham <chris.packham@alliedtelesis.co.nz>
Date: Fri Apr 17 10:19:08 2020 +1200
powerpc/setup_64: Set cache-line-size based on cache-block-size
commit 94c0b013c98583614e1ad911e8795ca36da34a85 upstream.
If {i,d}-cache-block-size is set and {i,d}-cache-line-size is not, use
the block-size value for both. Per the devicetree spec cache-line-size
is only needed if it differs from the block size.
Originally the code would fallback from block size to line size. An
error message was printed if both properties were missing.
Later the code was refactored to use clearer names and logic but it
inadvertently made line size a required property, meaning on systems
without a line size property we fall back to the default from the
cputable.
On powernv (OPAL) platforms, since the introduction of device tree CPU
features (5a61ef74f269 ("powerpc/64s: Support new device tree binding
for discovering CPU features")), that has led to the wrong value being
used, as the fallback value is incorrect for Power8/Power9 CPUs.
The incorrect values flow through to the VDSO and also to the sysconf
values, SC_LEVEL1_ICACHE_LINESIZE etc.
Fixes: bd067f83b084 ("powerpc/64: Fix naming of cache block vs. cache line")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reported-by: Qian Cai <cai@lca.pw>
[mpe: Add even more detail to change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200416221908.7886-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 144db1ea894425729350da23358a12866c8aa1a9
Author: Ahmad Fatoum <a.fatoum@pengutronix.de>
Date: Mon Mar 23 09:19:33 2020 +0100
ARM: imx: provide v7_cpu_resume() only on ARM_CPU_SUSPEND=y
commit f1baca8896ae18e12c45552a4c4ae2086aa7e02c upstream.
512a928affd5 ("ARM: imx: build v7_cpu_resume() unconditionally")
introduced an unintended linker error for i.MX6 configurations that have
ARM_CPU_SUSPEND=n which can happen if neither CONFIG_PM, CONFIG_CPU_IDLE,
nor ARM_PSCI_FW are selected.
Fix this by having v7_cpu_resume() compiled only when cpu_resume() it
calls is available as well.
The C declaration for the function remains unguarded to avoid future code
inadvertently using a stub and introducing a regression to the bug the
original commit fixed.
Cc: <stable@vger.kernel.org>
Fixes: 512a928affd5 ("ARM: imx: build v7_cpu_resume() unconditionally")
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Tested-by: Roland Hieber <rhi@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eed31992324fb6a07babafaec2aa78a2e0d78c28
Author: Mordechay Goodstein <mordechay.goodstein@intel.com>
Date: Fri Apr 17 10:08:10 2020 +0300
iwlwifi: mvm: beacon statistics shouldn't go backwards
commit 290d5e4951832e39d10f4184610dbf09038f8483 upstream.
We reset statistics also in case that we didn't reassoc so in
this cases keep last beacon counter.
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.1f9142751fbc.Ifbfd0f928a0a761110b8f4f2ca5483a61fb21131@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95df1045461544d06be2e9242f7bab33368947a6
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri Apr 17 10:08:09 2020 +0300
iwlwifi: pcie: actually release queue memory in TVQM
commit b98b33d5560a2d940f3b80f6768a6177bf3dfbc0 upstream.
The iwl_trans_pcie_dyn_txq_free() function only releases the frames
that may be left on the queue by calling iwl_pcie_gen2_txq_unmap(),
but doesn't actually free the DMA ring or byte-count tables for the
queue. This leads to pretty large memory leaks (at least before my
queue size improvements), in particular in monitor/sniffer mode on
channel hopping since this happens on every channel change.
This was also now more evident after the move to a DMA pool for the
byte count tables, showing messages such as
BUG iwlwifi:bc (...): Objects remaining in iwlwifi:bc on __kmem_cache_shutdown()
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=206811.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6b35ff91572f ("iwlwifi: pcie: introduce a000 TX queues management")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.f5f4c4193ec1.Id5feebc9b4318041913a9c89fc1378bb5454292c@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d49407334f0e3c77bd2f08b2873cebabcea0e0ac
Author: Gyeongtaek Lee <gt82.lee@samsung.com>
Date: Sat Apr 18 13:13:20 2020 +0900
ASoC: dapm: fixup dapm kcontrol widget
commit ebf1474745b4373fdde0fcf32d9d1f369b50b212 upstream.
snd_soc_dapm_kcontrol widget which is created by autodisable control
should contain correct on_val, mask and shift because it is set when the
widget is powered and changed value is applied on registers by following
code in dapm_seq_run_coalesced().
mask |= w->mask << w->shift;
if (w->power)
value |= w->on_val << w->shift;
else
value |= w->off_val << w->shift;
Shift on the mask in dapm_kcontrol_data_alloc() is removed to prevent
double shift.
And, on_val in dapm_kcontrol_set_value() is modified to get correct
value in the dapm_seq_run_coalesced().
Signed-off-by: Gyeongtaek Lee <gt82.lee@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/000001d61537$b212f620$1638e260$@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64c0c4832465cbef373b9f876511e1a4590c544d
Author: Paul Moore <paul@paul-moore.com>
Date: Mon Apr 20 16:24:34 2020 -0400
audit: check the length of userspace generated audit records
commit 763dafc520add02a1f4639b500c509acc0ea8e5b upstream.
Commit 756125289285 ("audit: always check the netlink payload length
in audit_receive_msg()") fixed a number of missing message length
checks, but forgot to check the length of userspace generated audit
records. The good news is that you need CAP_AUDIT_WRITE to submit
userspace audit records, which is generally only given to trusted
processes, so the impact should be limited.
Cc: stable@vger.kernel.org
Fixes: 756125289285 ("audit: always check the netlink payload length in audit_receive_msg()")
Reported-by: syzbot+49e69b4d71a420ceda3e@syzkaller.appspotmail.com
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddbfab6a4a85435eb10e08886038d0a814ba16a6
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Wed Apr 22 16:14:57 2020 -0400
usb-storage: Add unusual_devs entry for JMicron JMS566
commit 94f9c8c3c404ee1f7aaff81ad4f24aec4e34a78b upstream.
Cyril Roelandt reports that his JMicron JMS566 USB-SATA bridge fails
to handle WRITE commands with the FUA bit set, even though it claims
to support FUA. (Oddly enough, a later version of the same bridge,
version 2.03 as opposed to 1.14, doesn't claim to support FUA. Also
oddly, the bridge _does_ support FUA when using the UAS transport
instead of the Bulk-Only transport -- but this device was blacklisted
for uas in commit bc3bdb12bbb3 ("usb-storage: Disable UAS on JMicron
SATA enclosure") for apparently unrelated reasons.)
This patch adds a usb-storage unusual_devs entry with the BROKEN_FUA
flag. This allows the bridge to work properly with usb-storage.
Reported-and-tested-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221613110.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 150d35bf70d78d5ccc3964ece218fc44a67de620
Author: Jiri Slaby <jslaby@suse.cz>
Date: Fri Apr 17 12:59:59 2020 +0200
tty: rocket, avoid OOB access
commit 7127d24372bf23675a36edc64d092dc7fd92ebe8 upstream.
init_r_port can access pc104 array out of bounds. pc104 is a 2D array
defined to have 4 members. Each member has 8 submembers.
* we can have more than 4 (PCI) boards, i.e. [board] can be OOB
* line is not modulo-ed by anything, so the first line on the second
board can be 4, on the 3rd 12 or alike (depending on previously
registered boards). It's zero only on the first line of the first
board. So even [line] can be OOB, quite soon (with the 2nd registered
board already).
This code is broken for ages, so just avoid the OOB accesses and don't
try to fix it as we would need to find out the correct line number. Use
the default: RS232, if we are out.
Generally, if anyone needs to set the interface types, a module parameter
is past the last thing that should be used for this purpose. The
parameters' description says it's for ISA cards anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20200417105959.15201-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc919ba02b88fe9151baa806dbc469c2f254d5e7
Author: Andrew Melnychenko <andrew@daynix.com>
Date: Tue Apr 14 22:15:03 2020 +0300
tty: hvc: fix buffer overflow during hvc_alloc().
commit 9a9fc42b86c06120744555fea43fdcabe297c656 upstream.
If there is a lot(more then 16) of virtio-console devices
or virtio_console module is reloaded
- buffers 'vtermnos' and 'cons_ops' are overflowed.
In older kernels it overruns spinlock which leads to kernel freezing:
https://bugzilla.redhat.com/show_bug.cgi?id=1786239
To reproduce the issue, you can try simple script that
loads/unloads module. Something like this:
while [ 1 ]
do
modprobe virtio_console
sleep 2
modprobe -r virtio_console
sleep 2
done
Description of problem:
Guest get 'Call Trace' when loading module "virtio_console"
and unloading it frequently - clearly reproduced on kernel-4.18.0:
[ 81.498208] ------------[ cut here ]------------
[ 81.499263] pvqspinlock: lock 0xffffffff92080020 has corrupted value 0xc0774ca0!
[ 81.501000] WARNING: CPU: 0 PID: 785 at kernel/locking/qspinlock_paravirt.h:500 __pv_queued_spin_unlock_slowpath+0xc0/0xd0
[ 81.503173] Modules linked in: virtio_console fuse xt_CHECKSUM ipt_MASQUERADE xt_conntrack ipt_REJECT nft_counter nf_nat_tftp nft_objref nf_conntrack_tftp tun bridge stp llc nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nf_tables_set nft_chain_nat_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 nft_chain_route_ipv6 nft_chain_nat_ipv4 nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack nft_chain_route_ipv4 ip6_tables nft_compat ip_set nf_tables nfnetlink sunrpc bochs_drm drm_vram_helper ttm drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm i2c_piix4 pcspkr crct10dif_pclmul crc32_pclmul joydev ghash_clmulni_intel ip_tables xfs libcrc32c sd_mod sg ata_generic ata_piix virtio_net libata crc32c_intel net_failover failover serio_raw virtio_scsi dm_mirror dm_region_hash dm_log dm_mod [last unloaded: virtio_console]
[ 81.517019] CPU: 0 PID: 785 Comm: kworker/0:2 Kdump: loaded Not tainted 4.18.0-167.el8.x86_64 #1
[ 81.518639] Hardware name: Red Hat KVM, BIOS 1.12.0-5.scrmod+el8.2.0+5159+d8aa4d83 04/01/2014
[ 81.520205] Workqueue: events control_work_handler [virtio_console]
[ 81.521354] RIP: 0010:__pv_queued_spin_unlock_slowpath+0xc0/0xd0
[ 81.522450] Code: 07 00 48 63 7a 10 e8 bf 64 f5 ff 66 90 c3 8b 05 e6 cf d6 01 85 c0 74 01 c3 8b 17 48 89 fe 48 c7 c7 38 4b 29 91 e8 3a 6c fa ff <0f> 0b c3 0f 0b 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 48
[ 81.525830] RSP: 0018:ffffb51a01ffbd70 EFLAGS: 00010282
[ 81.526798] RAX: 0000000000000000 RBX: 0000000000000010 RCX: 0000000000000000
[ 81.528110] RDX: ffff9e66f1826480 RSI: ffff9e66f1816a08 RDI: ffff9e66f1816a08
[ 81.529437] RBP: ffffffff9153ff10 R08: 000000000000026c R09: 0000000000000053
[ 81.530732] R10: 0000000000000000 R11: ffffb51a01ffbc18 R12: ffff9e66cd682200
[ 81.532133] R13: ffffffff9153ff10 R14: ffff9e6685569500 R15: ffff9e66cd682000
[ 81.533442] FS: 0000000000000000(0000) GS:ffff9e66f1800000(0000) knlGS:0000000000000000
[ 81.534914] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 81.535971] CR2: 00005624c55b14d0 CR3: 00000003a023c000 CR4: 00000000003406f0
[ 81.537283] Call Trace:
[ 81.537763] __raw_callee_save___pv_queued_spin_unlock_slowpath+0x11/0x20
[ 81.539011] .slowpath+0x9/0xe
[ 81.539585] hvc_alloc+0x25e/0x300
[ 81.540237] init_port_console+0x28/0x100 [virtio_console]
[ 81.541251] handle_control_message.constprop.27+0x1c4/0x310 [virtio_console]
[ 81.542546] control_work_handler+0x70/0x10c [virtio_console]
[ 81.543601] process_one_work+0x1a7/0x3b0
[ 81.544356] worker_thread+0x30/0x390
[ 81.545025] ? create_worker+0x1a0/0x1a0
[ 81.545749] kthread+0x112/0x130
[ 81.546358] ? kthread_flush_work_fn+0x10/0x10
[ 81.547183] ret_from_fork+0x22/0x40
[ 81.547842] ---[ end trace aa97649bd16c8655 ]---
[ 83.546539] general protection fault: 0000 [#1] SMP NOPTI
[ 83.547422] CPU: 5 PID: 3225 Comm: modprobe Kdump: loaded Tainted: G W --------- - - 4.18.0-167.el8.x86_64 #1
[ 83.549191] Hardware name: Red Hat KVM, BIOS 1.12.0-5.scrmod+el8.2.0+5159+d8aa4d83 04/01/2014
[ 83.550544] RIP: 0010:__pv_queued_spin_lock_slowpath+0x19a/0x2a0
[ 83.551504] Code: c4 c1 ea 12 41 be 01 00 00 00 4c 8d 6d 14 41 83 e4 03 8d 42 ff 49 c1 e4 05 48 98 49 81 c4 40 a5 02 00 4c 03 24 c5 60 48 34 91 <49> 89 2c 24 b8 00 80 00 00 eb 15 84 c0 75 0a 41 0f b6 54 24 14 84
[ 83.554449] RSP: 0018:ffffb51a0323fdb0 EFLAGS: 00010202
[ 83.555290] RAX: 000000000000301c RBX: ffffffff92080020 RCX: 0000000000000001
[ 83.556426] RDX: 000000000000301d RSI: 0000000000000000 RDI: 0000000000000000
[ 83.557556] RBP: ffff9e66f196a540 R08: 000000000000028a R09: ffff9e66d2757788
[ 83.558688] R10: 0000000000000000 R11: 0000000000000000 R12: 646e61725f770b07
[ 83.559821] R13: ffff9e66f196a554 R14: 0000000000000001 R15: 0000000000180000
[ 83.560958] FS: 00007fd5032e8740(0000) GS:ffff9e66f1940000(0000) knlGS:0000000000000000
[ 83.562233] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 83.563149] CR2: 00007fd5022b0da0 CR3: 000000038c334000 CR4: 00000000003406e0
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200414191503.3471783-1-andrew@daynix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84b6c96bed46733c061f78b3f8963e9b1a2ed0dc
Author: Uros Bizjak <ubizjak@gmail.com>
Date: Tue Apr 14 09:14:14 2020 +0200
KVM: VMX: Enable machine check support for 32bit targets
commit fb56baae5ea509e63c2a068d66a4d8ea91969fca upstream.
There is no reason to limit the use of do_machine_check
to 64bit targets. MCE handling works for both target familes.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: stable@vger.kernel.org
Fixes: a0861c02a981 ("KVM: Add VT-x machine check support")
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Message-Id: <20200414071414.45636-1-ubizjak@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf8b99fba3a3cef403161f925e036d92654d33ef
Author: Sean Christopherson <sean.j.christopherson@intel.com>
Date: Tue Apr 7 23:40:58 2020 -0700
KVM: Check validity of resolved slot when searching memslots
commit b6467ab142b708dd076f6186ca274f14af379c72 upstream.
Check that the resolved slot (somewhat confusingly named 'start') is a
valid/allocated slot before doing the final comparison to see if the
specified gfn resides in the associated slot. The resolved slot can be
invalid if the binary search loop terminated because the search index
was incremented beyond the number of used slots.
This bug has existed since the binary search algorithm was introduced,
but went unnoticed because KVM statically allocated memory for the max
number of slots, i.e. the access would only be truly out-of-bounds if
all possible slots were allocated and the specified gfn was less than
the base of the lowest memslot. Commit 36947254e5f98 ("KVM: Dynamically
size memslot array based on number of used slots") eliminated the "all
possible slots allocated" condition and made the bug embarrasingly easy
to hit.
Fixes: 9c1a5d38780e6 ("kvm: optimize GFN to memslot lookup with large slots amount")
Reported-by: syzbot+d889b59b2bb87d4047a2@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200408064059.8957-2-sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cfcc37091baba19c2bfe46f16201edbca2aa40c
Author: Sean Christopherson <sean.j.christopherson@intel.com>
Date: Tue Apr 7 23:40:59 2020 -0700
KVM: s390: Return last valid slot if approx index is out-of-bounds
commit 97daa028f3f621adff2c4f7b15fe0874e5b5bd6c upstream.
Return the index of the last valid slot from gfn_to_memslot_approx() if
its binary search loop yielded an out-of-bounds index. The index can
be out-of-bounds if the specified gfn is less than the base of the
lowest memslot (which is also the last valid memslot).
Note, the sole caller, kvm_s390_get_cmma(), ensures used_slots is
non-zero.
Fixes: afdad61615cc3 ("KVM: s390: Fix storage attributes migration with memory slots")
Cc: stable@vger.kernel.org # 4.19.x: 0774a964ef56: KVM: Fix out of range accesses to memslots
Cc: stable@vger.kernel.org # 4.19.x
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200408064059.8957-3-sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c4e0cab837e0b2a3748f376828db426019c6252
Author: George Wilson <gcwilson@linux.ibm.com>
Date: Thu Mar 19 23:27:58 2020 -0400
tpm: ibmvtpm: retry on H_CLOSED in tpm_ibmvtpm_send()
commit eba5cf3dcb844c82f54d4a857e124824e252206d upstream.
tpm_ibmvtpm_send() can fail during PowerVM Live Partition Mobility resume
with an H_CLOSED return from ibmvtpm_send_crq(). The PAPR says, 'The
"partner partition suspended" transport event disables the associated CRQ
such that any H_SEND_CRQ hcall() to the associated CRQ returns H_Closed
until the CRQ has been explicitly enabled using the H_ENABLE_CRQ hcall.'
This patch adds a check in tpm_ibmvtpm_send() for an H_CLOSED return from
ibmvtpm_send_crq() and in that case calls tpm_ibmvtpm_resume() and
retries the ibmvtpm_send_crq() once.
Cc: stable@vger.kernel.org # 3.7.x
Fixes: 132f76294744 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Reported-by: Linh Pham <phaml@us.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: George Wilson <gcwilson@linux.ibm.com>
Tested-by: Linh Pham <phaml@us.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ede1d58c156e2735f2b6971b0ea39d4629da10f9
Author: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Date: Sun Apr 12 20:04:12 2020 +0300
tpm/tpm_tis: Free IRQ if probing fails
commit b160c94be5d2816b62c8ac338605668304242959 upstream.
Call disable_interrupts() if we have to revert to polling in order not to
unnecessarily reserve the IRQ for the life-cycle of the driver.
Cc: stable@vger.kernel.org # 4.5.x
Reported-by: Hans de Goede <hdegoede@redhat.com>
Fixes: e3837e74a06d ("tpm_tis: Refactor the interrupt setup")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65e3bab6948293998c3936fa881e40b6bcf7ac5c
Author: Alexander Tsoy <alexander@tsoy.me>
Date: Sat Apr 18 20:58:15 2020 +0300
ALSA: usb-audio: Filter out unsupported sample rates on Focusrite devices
commit 1c826792586f526a5a5cd21d55aad388f5bb0b23 upstream.
Many Focusrite devices supports a limited set of sample rates per
altsetting. These includes audio interfaces with ADAT ports:
- Scarlett 18i6, 18i8 1st gen, 18i20 1st gen;
- Scarlett 18i8 2nd gen, 18i20 2nd gen;
- Scarlett 18i8 3rd gen, 18i20 3rd gen;
- Clarett 2Pre USB, 4Pre USB, 8Pre USB.
Maximum rate is exposed in the last 4 bytes of Format Type descriptor
which has a non-standard bLength = 10.
Tested-by: Alexey Skobkin <skobkin-ru@ya.ru>
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200418175815.12211-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33bb5a4f25a2c7543141d10ac166599062c2d9d1
Author: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Date: Thu Apr 23 12:54:19 2020 +0800
ALSA: usb-audio: Fix usb audio refcnt leak when getting spdif
commit 59e1947ca09ebd1cae147c08c7c41f3141233c84 upstream.
snd_microii_spdif_default_get() invokes snd_usb_lock_shutdown(), which
increases the refcount of the snd_usb_audio object "chip".
When snd_microii_spdif_default_get() returns, local variable "chip"
becomes invalid, so the refcount should be decreased to keep refcount
balanced.
The reference counting issue happens in several exception handling paths
of snd_microii_spdif_default_get(). When those error scenarios occur
such as usb_ifnum_to_if() returns NULL, the function forgets to decrease
the refcnt increased by snd_usb_lock_shutdown(), causing a refcnt leak.
Fix this issue by jumping to "end" label when those error scenarios
occur.
Fixes: 447d6275f0c2 ("ALSA: usb-audio: Add sanity checks for endpoint accesses")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1587617711-13200-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee5a44badde58a33f417960cfae405be1e6a568d
Author: Kailang Yang <kailang@realtek.com>
Date: Thu Apr 23 14:18:31 2020 +0800
ALSA: hda/realtek - Add new codec supported for ALC245
commit 7fbdcd8301a84c09cebfa64f1317a6dafeec9188 upstream.
Enable new codec supported for ALC245.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/8c0804738b2c42439f59c39c8437817f@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 174bb908c7962027a41afa0af1ea765255d4c70e
Author: Takashi Iwai <tiwai@suse.de>
Date: Sat Apr 18 21:06:39 2020 +0200
ALSA: hda/realtek - Fix unexpected init_amp override
commit 67791202c5e069cf2ba51db0718d56c634709e78 upstream.
The commit 1c76aa5fb48d ("ALSA: hda/realtek - Allow skipping
spec->init_amp detection") changed the way to assign spec->init_amp
field that specifies the way to initialize the amp. Along with the
change, the commit also replaced a few fixups that set spec->init_amp
in HDA_FIXUP_ACT_PROBE with HDA_FIXUP_ACT_PRE_PROBE. This was rather
aligning to the other fixups, and not supposed to change the actual
behavior.
However, this change turned out to cause a regression on FSC S7020,
which hit exactly the above. The reason was that there is still one
place that overrides spec->init_amp after HDA_FIXUP_ACT_PRE_PROBE
call, namely in alc_ssid_check().
This patch fixes the regression by adding the proper spec->init_amp
override check, i.e. verifying whether it's still ALC_INIT_UNDEFINED.
Fixes: 1c76aa5fb48d ("ALSA: hda/realtek - Allow skipping spec->init_amp detection")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207329
Link: https://lore.kernel.org/r/20200418190639.10082-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db737117e97aff0e7bfb13689c8a7ce980ea9564
Author: Takashi Iwai <tiwai@suse.de>
Date: Mon Apr 20 09:55:29 2020 +0200
ALSA: usx2y: Fix potential NULL dereference
commit 7686e3485253635c529cdd5f416fc640abaf076f upstream.
The error handling code in usX2Y_rate_set() may hit a potential NULL
dereference when an error occurs before allocating all us->urb[].
Add a proper NULL check for fixing the corner case.
Reported-by: Lin Yi <teroincn@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200420075529.27203-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6db63ba00614992bad1d1dc52bb727cb5daf109
Author: Lucas Stach <l.stach@pengutronix.de>
Date: Mon Apr 20 18:14:23 2020 -0700
tools/vm: fix cross-compile build
commit cf01699ee220c38099eb3e43ce3d10690c8b7060 upstream.
Commit 7ed1c1901fe5 ("tools: fix cross-compile var clobbering") moved
the setup of the CC variable to tools/scripts/Makefile.include to make
the behavior consistent across all the tools Makefiles.
As the vm tools missed the include we end up with the wrong CC in a
cross-compiling evironment.
Fixes: 7ed1c1901fe5 (tools: fix cross-compile var clobbering)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Martin Kelly <martin@martingkelly.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200416104748.25243-1-l.stach@pengutronix.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35531951f04828c2445d6592a005c6245f4b14b7
Author: Muchun Song <songmuchun@bytedance.com>
Date: Mon Apr 20 18:14:04 2020 -0700
mm/ksm: fix NULL pointer dereference when KSM zero page is enabled
commit 56df70a63ed5d989c1d36deee94cae14342be6e9 upstream.
find_mergeable_vma() can return NULL. In this case, it leads to a crash
when we access vm_mm(its offset is 0x40) later in write_protect_page.
And this case did happen on our server. The following call trace is
captured in kernel 4.19 with the following patch applied and KSM zero
page enabled on our server.
commit e86c59b1b12d ("mm/ksm: improve deduplication of zero pages with colouring")
So add a vma check to fix it.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
Oops: 0000 [#1] SMP NOPTI
CPU: 9 PID: 510 Comm: ksmd Kdump: loaded Tainted: G OE 4.19.36.bsk.9-amd64 #4.19.36.bsk.9
RIP: try_to_merge_one_page+0xc7/0x760
Code: 24 58 65 48 33 34 25 28 00 00 00 89 e8 0f 85 a3 06 00 00 48 83 c4
60 5b 5d 41 5c 41 5d 41 5e 41 5f c3 48 8b 46 08 a8 01 75 b8 <49>
8b 44 24 40 4c 8d 7c 24 20 b9 07 00 00 00 4c 89 e6 4c 89 ff 48
RSP: 0018:ffffadbdd9fffdb0 EFLAGS: 00010246
RAX: ffffda83ffd4be08 RBX: ffffda83ffd4be40 RCX: 0000002c6e800000
RDX: 0000000000000000 RSI: ffffda83ffd4be40 RDI: 0000000000000000
RBP: ffffa11939f02ec0 R08: 0000000094e1a447 R09: 00000000abe76577
R10: 0000000000000962 R11: 0000000000004e6a R12: 0000000000000000
R13: ffffda83b1e06380 R14: ffffa18f31f072c0 R15: ffffda83ffd4be40
FS: 0000000000000000(0000) GS:ffffa0da43b80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000040 CR3: 0000002c77c0a003 CR4: 00000000007626e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
ksm_scan_thread+0x115e/0x1960
kthread+0xf5/0x130
ret_from_fork+0x1f/0x30
[songmuchun@bytedance.com: if the vma is out of date, just exit]
Link: http://lkml.kernel.org/r/20200416025034.29780-1-songmuchun@bytedance.com
[akpm@linux-foundation.org: add the conventional braces, replace /** with /*]
Fixes: e86c59b1b12d ("mm/ksm: improve deduplication of zero pages with colouring")
Co-developed-by: Xiongchun Duan <duanxiongchun@bytedance.com>
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Yang Shi <yang.shi@linux.alibaba.com>
Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Cc: Markus Elfring <Markus.Elfring@web.de>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200416025034.29780-1-songmuchun@bytedance.com
Link: http://lkml.kernel.org/r/20200414132905.83819-1-songmuchun@bytedance.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dcca7d2f751014d8caa3711e93b2119305e837df
Author: Longpeng <longpeng2@huawei.com>
Date: Mon Apr 20 18:13:51 2020 -0700
mm/hugetlb: fix a addressing exception caused by huge_pte_offset
commit 3c1d7e6ccb644d517a12f73a7ff200870926f865 upstream.
Our machine encountered a panic(addressing exception) after run for a
long time and the calltrace is:
RIP: hugetlb_fault+0x307/0xbe0
RSP: 0018:ffff9567fc27f808 EFLAGS: 00010286
RAX: e800c03ff1258d48 RBX: ffffd3bb003b69c0 RCX: e800c03ff1258d48
RDX: 17ff3fc00eda72b7 RSI: 00003ffffffff000 RDI: e800c03ff1258d48
RBP: ffff9567fc27f8c8 R08: e800c03ff1258d48 R09: 0000000000000080
R10: ffffaba0704c22a8 R11: 0000000000000001 R12: ffff95c87b4b60d8
R13: 00005fff00000000 R14: 0000000000000000 R15: ffff9567face8074
FS: 00007fe2d9ffb700(0000) GS:ffff956900e40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffd3bb003b69c0 CR3: 000000be67374000 CR4: 00000000003627e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
follow_hugetlb_page+0x175/0x540
__get_user_pages+0x2a0/0x7e0
__get_user_pages_unlocked+0x15d/0x210
__gfn_to_pfn_memslot+0x3c5/0x460 [kvm]
try_async_pf+0x6e/0x2a0 [kvm]
tdp_page_fault+0x151/0x2d0 [kvm]
...
kvm_arch_vcpu_ioctl_run+0x330/0x490 [kvm]
kvm_vcpu_ioctl+0x309/0x6d0 [kvm]
do_vfs_ioctl+0x3f0/0x540
SyS_ioctl+0xa1/0xc0
system_call_fastpath+0x22/0x27
For 1G hugepages, huge_pte_offset() wants to return NULL or pudp, but it
may return a wrong 'pmdp' if there is a race. Please look at the
following code snippet:
...
pud = pud_offset(p4d, addr);
if (sz != PUD_SIZE && pud_none(*pud))
return NULL;
/* hugepage or swap? */
if (pud_huge(*pud) || !pud_present(*pud))
return (pte_t *)pud;
pmd = pmd_offset(pud, addr);
if (sz != PMD_SIZE && pmd_none(*pmd))
return NULL;
/* hugepage or swap? */
if (pmd_huge(*pmd) || !pmd_present(*pmd))
return (pte_t *)pmd;
...
The following sequence would trigger this bug:
- CPU0: sz = PUD_SIZE and *pud = 0 , continue
- CPU0: "pud_huge(*pud)" is false
- CPU1: calling hugetlb_no_page and set *pud to xxxx8e7(PRESENT)
- CPU0: "!pud_present(*pud)" is false, continue
- CPU0: pmd = pmd_offset(pud, addr) and maybe return a wrong pmdp
However, we want CPU0 to return NULL or pudp in this case.
We must make sure there is exactly one dereference of pud and pmd.
Signed-off-by: Longpeng <longpeng2@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200413010342.771-1-longpeng2@huawei.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8da38eafa38b03c741aa63f688e5a77343a77be
Author: Jann Horn <jannh@google.com>
Date: Mon Apr 20 18:14:11 2020 -0700
vmalloc: fix remap_vmalloc_range() bounds checks
commit bdebd6a2831b6fab69eb85cee74a8ba77f1a1cc2 upstream.
remap_vmalloc_range() has had various issues with the bounds checks it
promises to perform ("This function checks that addr is a valid
vmalloc'ed area, and that it is big enough to cover the vma") over time,
e.g.:
- not detecting pgoff<<PAGE_SHIFT overflow
- not detecting (pgoff<<PAGE_SHIFT)+usize overflow
- not checking whether addr and addr+(pgoff<<PAGE_SHIFT) are the same
vmalloc allocation
- comparing a potentially wildly out-of-bounds pointer with the end of
the vmalloc region
In particular, since commit fc9702273e2e ("bpf: Add mmap() support for
BPF_MAP_TYPE_ARRAY"), unprivileged users can cause kernel null pointer
dereferences by calling mmap() on a BPF map with a size that is bigger
than the distance from the start of the BPF map to the end of the
address space.
This could theoretically be used as a kernel ASLR bypass, by using
whether mmap() with a given offset oopses or returns an error code to
perform a binary search over the possible address range.
To allow remap_vmalloc_range_partial() to verify that addr and
addr+(pgoff<<PAGE_SHIFT) are in the same vmalloc region, pass the offset
to remap_vmalloc_range_partial() instead of adding it to the pointer in
remap_vmalloc_range().
In remap_vmalloc_range_partial(), fix the check against
get_vm_area_size() by using size comparisons instead of pointer
comparisons, and add checks for pgoff.
Fixes: 833423143c3a ("[PATCH] mm: introduce remap_vmalloc_range()")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: Andrii Nakryiko <andriin@fb.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: KP Singh <kpsingh@chromium.org>
Link: http://lkml.kernel.org/r/20200415222312.236431-1-jannh@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6755e71c77520ae6e08c99d213448914245b515
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Wed Apr 22 16:09:51 2020 -0400
USB: hub: Fix handling of connect changes during sleep
commit 9f952e26295d977dbfc6fedeaf8c4f112c818d37 upstream.
Commit 8099f58f1ecd ("USB: hub: Don't record a connect-change event
during reset-resume") wasn't very well conceived. The problem it
tried to fix was that if a connect-change event occurred while the
system was asleep (such as a device disconnecting itself from the bus
when it is suspended and then reconnecting when it resumes)
requiring a reset-resume during the system wakeup transition, the hub
port's change_bit entry would remain set afterward. This would cause
the hub driver to believe another connect-change event had occurred
after the reset-resume, which was wrong and would lead the driver to
send unnecessary requests to the device (which could interfere with a
firmware update).
The commit tried to fix this by not setting the change_bit during the
wakeup. But this was the wrong thing to do; it means that when a
device is unplugged while the system is asleep, the hub driver doesn't
realize anything has happened: The change_bit flag which would tell it
to handle the disconnect event is clear.
The commit needs to be reverted and the problem fixed in a different
way. Fortunately an alternative solution was noted in the commit's
Changelog: We can continue to set the change_bit entry in
hub_activate() but then clear it when a reset-resume occurs. That way
the the hub driver will see the change_bit when a device is
disconnected but won't see it when the device is still present.
That's what this patch does.
Reported-and-tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8099f58f1ecd ("USB: hub: Don't record a connect-change event during reset-resume")
Tested-by: Paul Zimmerman <pauldzim@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221602480.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45ea77b75a604da875186519fea94997175c38e3
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Sat Mar 28 16:18:11 2020 -0400
USB: core: Fix free-while-in-use bug in the USB S-Glibrary
commit 056ad39ee9253873522f6469c3364964a322912b upstream.
FuzzUSB (a variant of syzkaller) found a free-while-still-in-use bug
in the USB scatter-gather library:
BUG: KASAN: use-after-free in atomic_read
include/asm-generic/atomic-instrumented.h:26 [inline]
BUG: KASAN: use-after-free in usb_hcd_unlink_urb+0x5f/0x170
drivers/usb/core/hcd.c:1607
Read of size 4 at addr ffff888065379610 by task kworker/u4:1/27
CPU: 1 PID: 27 Comm: kworker/u4:1 Not tainted 5.5.11 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.10.2-1ubuntu1 04/01/2014
Workqueue: scsi_tmf_2 scmd_eh_abort_handler
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xce/0x128 lib/dump_stack.c:118
print_address_description.constprop.4+0x21/0x3c0 mm/kasan/report.c:374
__kasan_report+0x153/0x1cb mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:639
check_memory_region_inline mm/kasan/generic.c:185 [inline]
check_memory_region+0x152/0x1b0 mm/kasan/generic.c:192
__kasan_check_read+0x11/0x20 mm/kasan/common.c:95
atomic_read include/asm-generic/atomic-instrumented.h:26 [inline]
usb_hcd_unlink_urb+0x5f/0x170 drivers/usb/core/hcd.c:1607
usb_unlink_urb+0x72/0xb0 drivers/usb/core/urb.c:657
usb_sg_cancel+0x14e/0x290 drivers/usb/core/message.c:602
usb_stor_stop_transport+0x5e/0xa0 drivers/usb/storage/transport.c:937
This bug occurs when cancellation of the S-G transfer races with
transfer completion. When that happens, usb_sg_cancel() may continue
to access the transfer's URBs after usb_sg_wait() has freed them.
The bug is caused by the fact that usb_sg_cancel() does not take any
sort of reference to the transfer, and so there is nothing to prevent
the URBs from being deallocated while the routine is trying to use
them. The fix is to take such a reference by incrementing the
transfer's io->count field while the cancellation is in progres and
decrementing it afterward. The transfer's URBs are not deallocated
until io->complete is triggered, which happens when io->count reaches
zero.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Kyungtae Kim <kt0755@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2003281615140.14837-100000@netrider.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d932c9f111742749a31ec1b0dc9562daabd3ab67
Author: Jann Horn <jannh@google.com>
Date: Wed Apr 1 09:46:19 2020 +0200
USB: early: Handle AMD's spec-compliant identifiers, too
commit 7dbdb53d72a51cea9b921d9dbba54be00752212a upstream.
This fixes a bug that causes the USB3 early console to freeze after
printing a single line on AMD machines because it can't parse the
Transfer TRB properly.
The spec at
https://www.intel.com/content/dam/www/public/us/en/documents/technical-specifications/extensible-host-controler-interface-usb-xhci.pdf
says in section "4.5.1 Device Context Index" that the Context Index,
also known as Endpoint ID according to
section "1.6 Terms and Abbreviations", is normally computed as
`DCI = (Endpoint Number * 2) + Direction`, which matches the current
definitions of XDBC_EPID_OUT and XDBC_EPID_IN.
However, the numbering in a Debug Capability Context data structure is
supposed to be different:
Section "7.6.3.2 Endpoint Contexts and Transfer Rings" explains that a
Debug Capability Context data structure has the endpoints mapped to indices
0 and 1.
Change XDBC_EPID_OUT/XDBC_EPID_IN to the spec-compliant values, add
XDBC_EPID_OUT_INTEL/XDBC_EPID_IN_INTEL with Intel's incorrect values, and
let xdbc_handle_tx_event() handle both.
I have verified that with this patch applied, the USB3 early console works
on both an Intel and an AMD machine.
Fixes: aeb9dd1de98c ("usb/early: Add driver for xhci debug capability")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20200401074619.8024-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 188551e1e883595a32c6b11f9183d38a1e455170
Author: Jonathan Cox <jonathan@jdcox.net>
Date: Fri Apr 10 14:24:27 2020 -0700
USB: Add USB_QUIRK_DELAY_CTRL_MSG and USB_QUIRK_DELAY_INIT for Corsair K70 RGB RAPIDFIRE
commit be34a5854b4606bd7a160ad3cb43415d623596c7 upstream.
The Corsair K70 RGB RAPIDFIRE needs the USB_QUIRK_DELAY_INIT and
USB_QUIRK_DELAY_CTRL_MSG to function or it will randomly not
respond on boot, just like other Corsair keyboards
Signed-off-by: Jonathan Cox <jonathan@jdcox.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200410212427.2886-1-jonathan@jdcox.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e129228a50b36e3f7a3ab3fc4f7667d57155563e
Author: Changming Liu <liu.changm@northeastern.edu>
Date: Mon Apr 20 23:41:25 2020 -0400
USB: sisusbvga: Change port variable from signed to unsigned
commit 2df7405f79ce1674d73c2786fe1a8727c905d65b upstream.
Change a bunch of arguments of wrapper functions which pass signed
integer to an unsigned integer which might cause undefined behaviors
when sign integer overflow.
Signed-off-by: Changming Liu <liu.changm@northeastern.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/BL0PR06MB45482D71EA822D75A0E60A2EE5D50@BL0PR06MB4548.namprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f511dc75d22e0c000fc70b54f670c2c17f5fba9a
Author: Piotr Krysiuk <piotras@gmail.com>
Date: Mon Apr 27 11:34:12 2020 +0100
fs/namespace.c: fix mountpoint reference counter race
A race condition between threads updating mountpoint reference counter
affects longterm releases 4.4.220, 4.9.220, 4.14.177 and 4.19.118.
The mountpoint reference counter corruption may occur when:
* one thread increments m_count member of struct mountpoint
[under namespace_sem, but not holding mount_lock]
pivot_root()
* another thread simultaneously decrements the same m_count
[under mount_lock, but not holding namespace_sem]
put_mountpoint()
unhash_mnt()
umount_mnt()
mntput_no_expire()
To fix this race condition, grab mount_lock before updating m_count in
pivot_root().
Reference: CVE-2020-12114
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d42466b626361e569f390c51c5063fa2a06e192
Author: Lars-Peter Clausen <lars@metafoo.de>
Date: Fri Apr 3 15:27:16 2020 +0200
iio: xilinx-xadc: Make sure not exceed maximum samplerate
commit 3b7f9dbb827ce8680b98490215e698b6079a9ec5 upstream.
The XADC supports a samplerate of up to 1MSPS. Unfortunately the hardware
does not have a FIFO, which means it generates an interrupt for each
conversion sequence. At one 1MSPS this creates an interrupt storm that
causes the system to soft-lock.
For this reason the driver limits the maximum samplerate to 150kSPS.
Currently this check is only done when setting a new samplerate. But it is
also possible that the initial samplerate configured in the FPGA bitstream
exceeds the limit.
In this case when starting to capture data without first changing the
samplerate the system can overload.
To prevent this check the currently configured samplerate in the probe
function and reduce it to the maximum if necessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bb4af3663df5dcae7a15f6bca32024a4b3377f2
Author: Lars-Peter Clausen <lars@metafoo.de>
Date: Fri Apr 3 15:27:15 2020 +0200
iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
commit 8bef455c8b1694547ee59e8b1939205ed9d901a6 upstream.
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96a0dc7e5e917afaf83b1104bc562d4fa262d8d9
Author: Lars-Peter Clausen <lars@metafoo.de>
Date: Fri Apr 3 15:27:14 2020 +0200
iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
commit f954b098fbac4d183219ce5b42d76d6df2aed50a upstream.
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66961103c061a46486368a8609ebca1b2921ecce
Author: Lars-Peter Clausen <lars@metafoo.de>
Date: Fri Apr 3 15:27:13 2020 +0200
iio: xilinx-xadc: Fix ADC-B powerdown
commit e44ec7794d88f918805d700240211a9ec05ed89d upstream.
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: bdc8cda1d010 ("iio:adc: Add Xilinx XADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7363ec6221aaafd9b276e637f4882075a6eeaf8c
Author: Olivier Moysan <olivier.moysan@st.com>
Date: Mon Mar 9 11:02:12 2020 +0100
iio: adc: stm32-adc: fix sleep in atomic context
commit e2042d2936dfc84e9c600fe9b9d0039ca0e54b7d upstream.
This commit fixes the following error:
"BUG: sleeping function called from invalid context at kernel/irq/chip.c"
In DMA mode suppress the trigger irq handler, and make the buffer
transfers directly in DMA callback, instead.
Fixes: 2763ea0585c9 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ea5de62b7b552d292b75e9ef55a28b4654a938f
Author: Lary Gibaud <yarl-baudig@mailoo.org>
Date: Sat Apr 11 17:16:06 2020 +0200
iio: st_sensors: rely on odr mask to know if odr can be set
commit e450e07c14abae563ad13b064cbce9fdccc6bc8d upstream.
Indeed, relying on addr being not 0 cannot work because some device have
their register to set odr at address 0. As a matter of fact, if the odr
can be set, then there is a mask.
Sensors with ODR register at address 0 are: lsm303dlh, lsm303dlhc, lsm303dlm
Fixes: 7d245172675a ("iio: common: st_sensors: check odr address value in st_sensors_set_odr()")
Signed-off-by: Lary Gibaud <yarl-baudig@mailoo.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee7ab2118a64d08add22e6c198dd1a36d0be02c7
Author: Lars Engebretsen <lars@engebretsen.ch>
Date: Wed Apr 15 12:10:43 2020 +0200
iio: core: remove extra semi-colon from devm_iio_device_register() macro
commit a07479147be03d2450376ebaff9ea1a0682f25d6 upstream.
This change removes the semi-colon from the devm_iio_device_register()
macro which seems to have been added by accident.
Fixes: 63b19547cc3d9 ("iio: Use macro magic to avoid manual assign of driver_module")
Signed-off-by: Lars Engebretsen <lars@engebretsen.ch>
Cc: <Stable@vger.kernel.org>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3189c4ab86447f8ab11d34c905b5d58e1a9c3e57
Author: Takashi Iwai <tiwai@suse.de>
Date: Wed Apr 22 13:33:20 2020 +0200
ALSA: usb-audio: Add connector notifier delegation
[ Upstream commit fef66ae73a611e84c8b4b74ff6f805ec5f113477 ]
It turned out that ALC1220-VB USB-audio device gives the interrupt
event to some PCM terminals while those don't allow the connector
state request but only the actual I/O terminals return the request.
The recent commit 7dc3c5a0172e ("ALSA: usb-audio: Don't create jack
controls for PCM terminals") excluded those phantom terminals, so
those events are ignored, too.
My first thought was that this could be easily deduced from the
associated terminals, but some of them have even no associate terminal
ID, hence it's not too trivial to figure out.
Since the number of such terminals are small and limited, this patch
implements another quirk table for the simple mapping of the
connectors. It's not really scalable, but let's hope that there will
be not many such funky devices in future.
Fixes: 7dc3c5a0172e ("ALSA: usb-audio: Don't create jack controls for PCM terminals")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206873
Link: https://lore.kernel.org/r/20200422113320.26664-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cd6bc48f9f8040057c31edd76ccbd743df019933
Author: Takashi Iwai <tiwai@suse.de>
Date: Mon Apr 20 08:20:36 2020 +0200
ALSA: usb-audio: Add static mapping table for ALC1220-VB-based mobos
[ Upstream commit a43c1c41bc5145971d06edc42a6b1e8faa0e2bc3 ]
TRX40 mobos from MSI and others with ALC1220-VB USB-audio device need
yet more quirks for the proper control names.
This patch provides the mapping table for those boards, correcting the
FU names for volume and mute controls as well as the terminal names
for jack controls. It also improves build_connector_control() not to
add the directional suffix blindly if the string is given from the
mapping table.
With this patch applied, the new UCM profiles will be effective.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=206873
Link: https://lore.kernel.org/r/20200420062036.28567-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4f3dab13cd243f0d21f7d68005b3492cbdc2d53f
Author: Takashi Iwai <tiwai@suse.de>
Date: Sun Apr 19 09:19:26 2020 +0200
ALSA: hda: Remove ASUS ROG Zenith from the blacklist
[ Upstream commit a8cf44f085ac12c0b5b8750ebb3b436c7f455419 ]
The commit 3c6fd1f07ed0 ("ALSA: hda: Add driver blacklist") added a
new blacklist for the devices that are known to have empty codecs, and
one of the entries was ASUS ROG Zenith II (PCI SSID 1043:874f).
However, it turned out that the very same PCI SSID is used for the
previous model that does have the valid HD-audio codecs and the change
broke the sound on it.
This patch reverts the corresponding entry as a temporary solution.
Although Zenith II and co will see get the empty HD-audio bus again,
it'd be merely resource wastes and won't affect the functionality,
so it's no end of the world. We'll need to address this later,
e.g. by either switching to DMI string matching or using PCI ID &
SSID pairs.
Fixes: 3c6fd1f07ed0 ("ALSA: hda: Add driver blacklist")
Reported-by: Johnathan Smithinovic <johnathan.smithinovic@gmx.at>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200419071926.22683-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e4a281c7daa07814748179ee8b4b483124bb94ea
Author: Waiman Long <longman@redhat.com>
Date: Sat Mar 21 21:11:25 2020 -0400
KEYS: Avoid false positive ENOMEM error on key read
[ Upstream commit 4f0882491a148059a52480e753b7f07fc550e188 ]
By allocating a kernel buffer with a user-supplied buffer length, it
is possible that a false positive ENOMEM error may be returned because
the user-supplied length is just too large even if the system do have
enough memory to hold the actual key data.
Moreover, if the buffer length is larger than the maximum amount of
memory that can be returned by kmalloc() (2^(MAX_ORDER-1) number of
pages), a warning message will also be printed.
To reduce this possibility, we set a threshold (PAGE_SIZE) over which we
do check the actual key length first before allocating a buffer of the
right size to hold it. The threshold is arbitrary, it is just used to
trigger a buffer length check. It does not limit the actual key length
as long as there is enough memory to satisfy the memory request.
To further avoid large buffer allocation failure due to page
fragmentation, kvmalloc() is used to allocate the buffer so that vmapped
pages can be used when there is not a large enough contiguous set of
pages available for allocation.
In the extremely unlikely scenario that the key keeps on being changed
and made longer (still <= buflen) in between 2 __keyctl_read_key()
calls, the __keyctl_read_key() calling loop in keyctl_read_key() may
have to be iterated a large number of times, but definitely not infinite.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b9d1ba5dd94009ae91aacf959801668b8ac9a2fe
Author: Dan Carpenter <dan.carpenter@oracle.com>
Date: Wed Apr 22 12:36:41 2020 +0300
mlxsw: Fix some IS_ERR() vs NULL bugs
[ Upstream commit c391eb8366ae052d571bb2841f1ccb4d39f3ceb8 ]
The mlxsw_sp_acl_rulei_create() function is supposed to return an error
pointer from mlxsw_afa_block_create(). The problem is that these
functions both return NULL instead of error pointers. Half the callers
expect NULL and half expect error pointers so it could lead to a NULL
dereference on failure.
This patch changes both of them to return error pointers and changes all
the callers which checked for NULL to check for IS_ERR() instead.
Fixes: 4cda7d8d7098 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c39723ccc47d6454df44e1d1cf8af1d31abc2be4
Author: David Ahern <dsahern@gmail.com>
Date: Mon Apr 20 17:13:52 2020 -0600
vrf: Check skb for XFRM_TRANSFORMED flag
[ Upstream commit 16b9db1ce34ff00d6c18e82825125cfef0cdfb13 ]
To avoid a loop with qdiscs and xfrms, check if the skb has already gone
through the qdisc attached to the VRF device and then to the xfrm layer.
If so, no need for a second redirect.
Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Reported-by: Trev Larock <trev@larock.ca>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 995908dc5b51bfb42edf69160b0dd062d97ee07e
Author: David Ahern <dsahern@gmail.com>
Date: Mon Apr 20 17:13:51 2020 -0600
xfrm: Always set XFRM_TRANSFORMED in xfrm{4,6}_output_finish
[ Upstream commit 0c922a4850eba2e668f73a3f1153196e09abb251 ]
IPSKB_XFRM_TRANSFORMED and IP6SKB_XFRM_TRANSFORMED are skb flags set by
xfrm code to tell other skb handlers that the packet has been passed
through the xfrm output functions. Simplify the code and just always
set them rather than conditionally based on netfilter enabled thus
making the flag available for other users.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4dbc99162edd95a2195ba2f7518704140c9a76a3
Author: Florian Fainelli <f.fainelli@gmail.com>
Date: Mon Apr 20 20:26:55 2020 -0700
net: dsa: b53: b53_arl_rw_op() needs to select IVL or SVL
[ Upstream commit 64fec9493f7dc9bdd7233bcfe98985c45bd0e3c1 ]
Flip the IVL_SVL_SELECT bit correctly based on the VLAN enable status,
the default is to perform Shared VLAN learning instead of Individual
learning.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e14d2aef2fcd9d1e7523858ac0f2103162f8f8f
Author: Florian Fainelli <f.fainelli@gmail.com>
Date: Mon Apr 20 20:26:54 2020 -0700
net: dsa: b53: Rework ARL bin logic
[ Upstream commit 6344dbde6a27d10d16246d734b968f84887841e2 ]
When asking the ARL to read a MAC address, we will get a number of bins
returned in a single read. Out of those bins, there can essentially be 3
states:
- all bins are full, we have no space left, and we can either replace an
existing address or return that full condition
- the MAC address was found, then we need to return its bin index and
modify that one, and only that one
- the MAC address was not found and we have a least one bin free, we use
that bin index location then
The code would unfortunately fail on all counts.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f1653eee163f1bc2d6304c58be56a471a965682
Author: Florian Fainelli <f.fainelli@gmail.com>
Date: Mon Apr 20 20:26:53 2020 -0700
net: dsa: b53: Fix ARL register definitions
[ Upstream commit c2e77a18a7ed65eb48f6e389b6a59a0fd753646a ]
The ARL {MAC,VID} tuple and the forward entry were off by 0x10 bytes,
which means that when we read/wrote from/to ARL bin index 0, we were
actually accessing the ARLA_RWCTRL register.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a224e376938fce615ba702668d946f0276b517c7
Author: Florian Fainelli <f.fainelli@gmail.com>
Date: Mon Apr 20 20:26:51 2020 -0700
net: dsa: b53: Lookup VID in ARL searches when VLAN is enabled
[ Upstream commit 2e97b0cd1651a270f3a3fcf42115c51f3284c049 ]
When VLAN is enabled, and an ARL search is issued, we also need to
compare the full {MAC,VID} tuple before returning a successful search
result.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abc103cd536817a9c525175e561d9bbe2d610968
Author: David Ahern <dsahern@gmail.com>
Date: Tue Apr 21 17:48:27 2020 -0600
vrf: Fix IPv6 with qdisc and xfrm
[ Upstream commit a53c102872ad6e34e1518e25899dc9498c27f8b1 ]
When a qdisc is attached to the VRF device, the packet goes down the ndo
xmit function which is setup to send the packet back to the VRF driver
which does a lookup to send the packet out. The lookup in the VRF driver
is not considering xfrm policies. Change it to use ip6_dst_lookup_flow
rather than ip6_route_output.
Fixes: 35402e313663 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efa7382a0f04d6679d5ceb4f1bbf306d0f6fd95c
Author: Taehee Yoo <ap420073@gmail.com>
Date: Mon Apr 20 15:01:33 2020 +0000
team: fix hang in team_mode_get()
[ Upstream commit 1c30fbc76b8f0c07c92a8ca4cd7c456612e17eb5 ]
When team mode is changed or set, the team_mode_get() is called to check
whether the mode module is inserted or not. If the mode module is not
inserted, it calls the request_module().
In the request_module(), it creates a child process, which is
the "modprobe" process and waits for the done of the child process.
At this point, the following locks were used.
down_read(&cb_lock()); by genl_rcv()
genl_lock(); by genl_rcv_msc()
rtnl_lock(); by team_nl_cmd_options_set()
mutex_lock(&team->lock); by team_nl_team_get()
Concurrently, the team module could be removed by rmmod or "modprobe -r"
The __exit function of team module is team_module_exit(), which calls
team_nl_fini() and it tries to acquire following locks.
down_write(&cb_lock);
genl_lock();
Because of the genl_lock() and cb_lock, this process can't be finished
earlier than request_module() routine.
The problem secenario.
CPU0 CPU1
team_mode_get
request_module()
modprobe -r team_mode_roundrobin
team <--(B)
modprobe team <--(A)
team_mode_roundrobin
By request_module(), the "modprobe team_mode_roundrobin" command
will be executed. At this point, the modprobe process will decide
that the team module should be inserted before team_mode_roundrobin.
Because the team module is being removed.
By the module infrastructure, the same module insert/remove operations
can't be executed concurrently.
So, (A) waits for (B) but (B) also waits for (A) because of locks.
So that the hang occurs at this point.
Test commands:
while :
do
teamd -d &
killall teamd &
modprobe -rv team_mode_roundrobin &
done
The approach of this patch is to hold the reference count of the team
module if the team module is compiled as a module. If the reference count
of the team module is not zero while request_module() is being called,
the team module will not be removed at that moment.
So that the above scenario could not occur.
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3405bf51f6d861dd127e72df048a6e0d1581f7a8
Author: Eric Dumazet <edumazet@google.com>
Date: Fri Apr 17 07:10:23 2020 -0700
tcp: cache line align MAX_TCP_HEADER
[ Upstream commit 9bacd256f1354883d3c1402655153367982bba49 ]
TCP stack is dumb in how it cooks its output packets.
Depending on MAX_HEADER value, we might chose a bad ending point
for the headers.
If we align the end of TCP headers to cache line boundary, we
make sure to always use the smallest number of cache lines,
which always help.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ee7ced6468349f12a7094ac93f8e66c43064248
Author: Eric Dumazet <edumazet@google.com>
Date: Tue Apr 21 10:00:28 2020 -0700
sched: etf: do not assume all sockets are full blown
[ Upstream commit a1211bf9a7774706722ba3b18c6157d980319f79 ]
skb->sk does not always point to a full blown socket,
we need to use sk_fullsock() before accessing fields which
only make sense on full socket.
BUG: KASAN: use-after-free in report_sock_error+0x286/0x300 net/sched/sch_etf.c:141
Read of size 1 at addr ffff88805eb9b245 by task syz-executor.5/9630
CPU: 1 PID: 9630 Comm: syz-executor.5 Not tainted 5.7.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x188/0x20d lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd3/0x315 mm/kasan/report.c:382
__kasan_report.cold+0x35/0x4d mm/kasan/report.c:511
kasan_report+0x33/0x50 mm/kasan/common.c:625
report_sock_error+0x286/0x300 net/sched/sch_etf.c:141
etf_enqueue_timesortedlist+0x389/0x740 net/sched/sch_etf.c:170
__dev_xmit_skb net/core/dev.c:3710 [inline]
__dev_queue_xmit+0x154a/0x30a0 net/core/dev.c:4021
neigh_hh_output include/net/neighbour.h:499 [inline]
neigh_output include/net/neighbour.h:508 [inline]
ip6_finish_output2+0xfb5/0x25b0 net/ipv6/ip6_output.c:117
__ip6_finish_output+0x442/0xab0 net/ipv6/ip6_output.c:143
ip6_finish_output+0x34/0x1f0 net/ipv6/ip6_output.c:153
NF_HOOK_COND include/linux/netfilter.h:296 [inline]
ip6_output+0x239/0x810 net/ipv6/ip6_output.c:176
dst_output include/net/dst.h:435 [inline]
NF_HOOK include/linux/netfilter.h:307 [inline]
NF_HOOK include/linux/netfilter.h:301 [inline]
ip6_xmit+0xe1a/0x2090 net/ipv6/ip6_output.c:280
tcp_v6_send_synack+0x4e7/0x960 net/ipv6/tcp_ipv6.c:521
tcp_rtx_synack+0x10d/0x1a0 net/ipv4/tcp_output.c:3916
inet_rtx_syn_ack net/ipv4/inet_connection_sock.c:669 [inline]
reqsk_timer_handler+0x4c2/0xb40 net/ipv4/inet_connection_sock.c:763
call_timer_fn+0x1ac/0x780 kernel/time/timer.c:1405
expire_timers kernel/time/timer.c:1450 [inline]
__run_timers kernel/time/timer.c:1774 [inline]
__run_timers kernel/time/timer.c:1741 [inline]
run_timer_softirq+0x623/0x1600 kernel/time/timer.c:1787
__do_softirq+0x26c/0x9f7 kernel/softirq.c:292
invoke_softirq kernel/softirq.c:373 [inline]
irq_exit+0x192/0x1d0 kernel/softirq.c:413
exiting_irq arch/x86/include/asm/apic.h:546 [inline]
smp_apic_timer_interrupt+0x19e/0x600 arch/x86/kernel/apic/apic.c:1140
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:829
</IRQ>
RIP: 0010:des_encrypt+0x157/0x9c0 lib/crypto/des.c:792
Code: 85 22 06 00 00 41 31 dc 41 8b 4d 04 44 89 e2 41 83 e4 3f 4a 8d 3c a5 60 72 72 88 81 e2 3f 3f 3f 3f 48 89 f8 48 c1 e8 03 31 d9 <0f> b6 34 28 48 89 f8 c1 c9 04 83 e0 07 83 c0 03 40 38 f0 7c 09 40
RSP: 0018:ffffc90003b5f6c0 EFLAGS: 00000282 ORIG_RAX: ffffffffffffff13
RAX: 1ffffffff10e4e55 RBX: 00000000d2f846d0 RCX: 00000000d2f846d0
RDX: 0000000012380612 RSI: ffffffff839863ca RDI: ffffffff887272a8
RBP: dffffc0000000000 R08: ffff888091d0a380 R09: 0000000000800081
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000012
R13: ffff8880a8ae8078 R14: 00000000c545c93e R15: 0000000000000006
cipher_crypt_one crypto/cipher.c:75 [inline]
crypto_cipher_encrypt_one+0x124/0x210 crypto/cipher.c:82
crypto_cbcmac_digest_update+0x1b5/0x250 crypto/ccm.c:830
crypto_shash_update+0xc4/0x120 crypto/shash.c:119
shash_ahash_update+0xa3/0x110 crypto/shash.c:246
crypto_ahash_update include/crypto/hash.h:547 [inline]
hash_sendmsg+0x518/0xad0 crypto/algif_hash.c:102
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:672
____sys_sendmsg+0x308/0x7e0 net/socket.c:2362
___sys_sendmsg+0x100/0x170 net/socket.c:2416
__sys_sendmmsg+0x195/0x480 net/socket.c:2506
__do_sys_sendmmsg net/socket.c:2535 [inline]
__se_sys_sendmmsg net/socket.c:2532 [inline]
__x64_sys_sendmmsg+0x99/0x100 net/socket.c:2532
do_syscall_64+0xf6/0x7d0 arch/x86/entry/common.c:295
entry_SYSCALL_64_after_hwframe+0x49/0xb3
RIP: 0033:0x45c829
Code: 0d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 db b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f6d9528ec78 EFLAGS: 00000246 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 00000000004fc080 RCX: 000000000045c829
RDX: 0000000000000001 RSI: 0000000020002640 RDI: 0000000000000004
RBP: 000000000078bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000000008d7 R14: 00000000004cb7aa R15: 00007f6d9528f6d4
Fixes: 4b15c7075352 ("net/sched: Make etf report drops on error_queue")
Fixes: 25db26a91364 ("net/sched: Introduce the ETF Qdisc")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9ef1c552418eebb669723f414940a605c7d4557
Author: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Date: Thu Apr 23 13:13:03 2020 +0800
net/x25: Fix x25_neigh refcnt leak when receiving frame
[ Upstream commit f35d12971b4d814cdb2f659d76b42f0c545270b6 ]
x25_lapb_receive_frame() invokes x25_get_neigh(), which returns a
reference of the specified x25_neigh object to "nb" with increased
refcnt.
When x25_lapb_receive_frame() returns, local variable "nb" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one path of
x25_lapb_receive_frame(). When pskb_may_pull() returns false, the
function forgets to decrease the refcnt increased by x25_get_neigh(),
causing a refcnt leak.
Fix this issue by calling x25_neigh_put() when pskb_may_pull() returns
false.
Fixes: cb101ed2c3c7 ("x25: Handle undersized/fragmented skbs")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 134831fa2ba1e760b7fbb2e41b832617b83a9316
Author: Marc Zyngier <maz@kernel.org>
Date: Sat Apr 18 19:14:57 2020 +0100
net: stmmac: dwmac-meson8b: Add missing boundary to RGMII TX clock array
[ Upstream commit f0212a5ebfa6cd789ab47666b9cc169e6e688732 ]
Running with KASAN on a VIM3L systems leads to the following splat
when probing the Ethernet device:
==================================================================
BUG: KASAN: global-out-of-bounds in _get_maxdiv+0x74/0xd8
Read of size 4 at addr ffffa000090615f4 by task systemd-udevd/139
CPU: 1 PID: 139 Comm: systemd-udevd Tainted: G E 5.7.0-rc1-00101-g8624b7577b9c #781
Hardware name: amlogic w400/w400, BIOS 2020.01-rc5 03/12/2020
Call trace:
dump_backtrace+0x0/0x2a0
show_stack+0x20/0x30
dump_stack+0xec/0x148
print_address_description.isra.12+0x70/0x35c
__kasan_report+0xfc/0x1d4
kasan_report+0x4c/0x68
__asan_load4+0x9c/0xd8
_get_maxdiv+0x74/0xd8
clk_divider_bestdiv+0x74/0x5e0
clk_divider_round_rate+0x80/0x1a8
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_hw_round_rate+0xac/0xf0
clk_factor_round_rate+0xb8/0xd0
clk_core_determine_round_nolock.part.9+0x9c/0xd0
clk_core_round_rate_nolock+0xf0/0x108
clk_core_round_rate_nolock+0xbc/0x108
clk_core_set_rate_nolock+0xc4/0x2e8
clk_set_rate+0x58/0xe0
meson8b_dwmac_probe+0x588/0x72c [dwmac_meson8b]
platform_drv_probe+0x78/0xd8
really_probe+0x158/0x610
driver_probe_device+0x140/0x1b0
device_driver_attach+0xa4/0xb0
__driver_attach+0xcc/0x1c8
bus_for_each_dev+0xf4/0x168
driver_attach+0x3c/0x50
bus_add_driver+0x238/0x2e8
driver_register+0xc8/0x1e8
__platform_driver_register+0x88/0x98
meson8b_dwmac_driver_init+0x28/0x1000 [dwmac_meson8b]
do_one_initcall+0xa8/0x328
do_init_module+0xe8/0x368
load_module+0x3300/0x36b0
__do_sys_finit_module+0x120/0x1a8
__arm64_sys_finit_module+0x4c/0x60
el0_svc_common.constprop.2+0xe4/0x268
do_el0_svc+0x98/0xa8
el0_svc+0x24/0x68
el0_sync_handler+0x12c/0x318
el0_sync+0x158/0x180
The buggy address belongs to the variable:
div_table.63646+0x34/0xfffffffffffffa40 [dwmac_meson8b]
Memory state around the buggy address:
ffffa00009061480: fa fa fa fa 00 00 00 01 fa fa fa fa 00 00 00 00
ffffa00009061500: 05 fa fa fa fa fa fa fa 00 04 fa fa fa fa fa fa
>ffffa00009061580: 00 03 fa fa fa fa fa fa 00 00 00 00 00 00 fa fa
^
ffffa00009061600: fa fa fa fa 00 01 fa fa fa fa fa fa 01 fa fa fa
ffffa00009061680: fa fa fa fa 00 01 fa fa fa fa fa fa 04 fa fa fa
==================================================================
Digging into this indeed shows that the clock divider array is
lacking a final fence, and that the clock subsystems goes in the
weeds. Oh well.
Let's add the empty structure that indicates the end of the array.
Fixes: bd6f48546b9c ("net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 275828d499f2633fa3103ecdb3ed19bd00a02965
Author: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Date: Wed Apr 15 16:36:19 2020 +0800
net: netrom: Fix potential nr_neigh refcnt leak in nr_add_node
[ Upstream commit d03f228470a8c0a22b774d1f8d47071e0de4f6dd ]
nr_add_node() invokes nr_neigh_get_dev(), which returns a local
reference of the nr_neigh object to "nr_neigh" with increased refcnt.
When nr_add_node() returns, "nr_neigh" becomes invalid, so the refcount
should be decreased to keep refcount balanced.
The issue happens in one normal path of nr_add_node(), which forgets to
decrease the refcnt increased by nr_neigh_get_dev() and causes a refcnt
leak. It should decrease the refcnt before the function returns like
other normal paths do.
Fix this issue by calling nr_neigh_put() before the nr_add_node()
returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f71003197dd97e197f30ecdde5e58d205b940e7c
Author: Doug Berger <opendmb@gmail.com>
Date: Thu Apr 23 15:44:17 2020 -0700
net: bcmgenet: correct per TX/RX ring statistics
[ Upstream commit a6d0b83f25073bdf08b8547aeff961a62c6ab229 ]
The change to track net_device_stats per ring to better support SMP
missed updating the rx_dropped member.
The ndo_get_stats method is also needed to combine the results for
ethtool statistics (-S) before filling in the ethtool structure.
Fixes: 37a30b435b92 ("net: bcmgenet: Track per TX/RX rings statistics")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d7ea5675e0f7dcf08b10056045ba369cf915557
Author: Taehee Yoo <ap420073@gmail.com>
Date: Mon Apr 20 13:29:40 2020 +0000
macvlan: fix null dereference in macvlan_device_event()
[ Upstream commit 4dee15b4fd0d61ec6bbd179238191e959d34cf7a ]
In the macvlan_device_event(), the list_first_entry_or_null() is used.
This function could return null pointer if there is no node.
But, the macvlan module doesn't check the null pointer.
So, null-ptr-deref would occur.
bond0
|
+----+-----+
| |
macvlan0 macvlan1
| |
dummy0 dummy1
The problem scenario.
If dummy1 is removed,
1. ->dellink() of dummy1 is called.
2. NETDEV_UNREGISTER of dummy1 notification is sent to macvlan module.
3. ->dellink() of macvlan1 is called.
4. NETDEV_UNREGISTER of macvlan1 notification is sent to bond module.
5. __bond_release_one() is called and it internally calls
dev_set_mac_address().
6. dev_set_mac_address() calls the ->ndo_set_mac_address() of macvlan1,
which is macvlan_set_mac_address().
7. macvlan_set_mac_address() calls the dev_set_mac_address() with dummy1.
8. NETDEV_CHANGEADDR of dummy1 is sent to macvlan module.
9. In the macvlan_device_event(), it calls list_first_entry_or_null().
At this point, dummy1 and macvlan1 were removed.
So, list_first_entry_or_null() will return NULL.
Test commands:
ip netns add nst
ip netns exec nst ip link add bond0 type bond
for i in {0..10}
do
ip netns exec nst ip link add dummy$i type dummy
ip netns exec nst ip link add macvlan$i link dummy$i \
type macvlan mode passthru
ip netns exec nst ip link set macvlan$i master bond0
done
ip netns del nst
Splat looks like:
[ 40.585687][ T146] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP DEI
[ 40.587249][ T146] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
[ 40.588342][ T146] CPU: 1 PID: 146 Comm: kworker/u8:2 Not tainted 5.7.0-rc1+ #532
[ 40.589299][ T146] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 40.590469][ T146] Workqueue: netns cleanup_net
[ 40.591045][ T146] RIP: 0010:macvlan_device_event+0x4e2/0x900 [macvlan]
[ 40.591905][ T146] Code: 00 00 00 00 00 fc ff df 80 3c 06 00 0f 85 45 02 00 00 48 89 da 48 b8 00 00 00 00 00 fc ff d2
[ 40.594126][ T146] RSP: 0018:ffff88806116f4a0 EFLAGS: 00010246
[ 40.594783][ T146] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 40.595653][ T146] RDX: 0000000000000000 RSI: ffff88806547ddd8 RDI: ffff8880540f1360
[ 40.596495][ T146] RBP: ffff88804011a808 R08: fffffbfff4fb8421 R09: fffffbfff4fb8421
[ 40.597377][ T146] R10: ffffffffa7dc2107 R11: 0000000000000000 R12: 0000000000000008
[ 40.598186][ T146] R13: ffff88804011a000 R14: ffff8880540f1000 R15: 1ffff1100c22de9a
[ 40.599012][ T146] FS: 0000000000000000(0000) GS:ffff888067800000(0000) knlGS:0000000000000000
[ 40.600004][ T146] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 40.600665][ T146] CR2: 00005572d3a807b8 CR3: 000000005fcf4003 CR4: 00000000000606e0
[ 40.601485][ T146] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 40.602461][ T146] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 40.603443][ T146] Call Trace:
[ 40.603871][ T146] ? nf_tables_dump_setelem+0xa0/0xa0 [nf_tables]
[ 40.604587][ T146] ? macvlan_uninit+0x100/0x100 [macvlan]
[ 40.605212][ T146] ? __module_text_address+0x13/0x140
[ 40.605842][ T146] notifier_call_chain+0x90/0x160
[ 40.606477][ T146] dev_set_mac_address+0x28e/0x3f0
[ 40.607117][ T146] ? netdev_notify_peers+0xc0/0xc0
[ 40.607762][ T146] ? __module_text_address+0x13/0x140
[ 40.608440][ T146] ? notifier_call_chain+0x90/0x160
[ 40.609097][ T146] ? dev_set_mac_address+0x1f0/0x3f0
[ 40.609758][ T146] dev_set_mac_address+0x1f0/0x3f0
[ 40.610402][ T146] ? __local_bh_enable_ip+0xe9/0x1b0
[ 40.611071][ T146] ? bond_hw_addr_flush+0x77/0x100 [bonding]
[ 40.611823][ T146] ? netdev_notify_peers+0xc0/0xc0
[ 40.612461][ T146] ? bond_hw_addr_flush+0x77/0x100 [bonding]
[ 40.613213][ T146] ? bond_hw_addr_flush+0x77/0x100 [bonding]
[ 40.613963][ T146] ? __local_bh_enable_ip+0xe9/0x1b0
[ 40.614631][ T146] ? bond_time_in_interval.isra.31+0x90/0x90 [bonding]
[ 40.615484][ T146] ? __bond_release_one+0x9f0/0x12c0 [bonding]
[ 40.616230][ T146] __bond_release_one+0x9f0/0x12c0 [bonding]
[ 40.616949][ T146] ? bond_enslave+0x47c0/0x47c0 [bonding]
[ 40.617642][ T146] ? lock_downgrade+0x730/0x730
[ 40.618218][ T146] ? check_flags.part.42+0x450/0x450
[ 40.618850][ T146] ? __mutex_unlock_slowpath+0xd0/0x670
[ 40.619519][ T146] ? trace_hardirqs_on+0x30/0x180
[ 40.620117][ T146] ? wait_for_completion+0x250/0x250
[ 40.620754][ T146] bond_netdev_event+0x822/0x970 [bonding]
[ 40.621460][ T146] ? __module_text_address+0x13/0x140
[ 40.622097][ T146] notifier_call_chain+0x90/0x160
[ 40.622806][ T146] rollback_registered_many+0x660/0xcf0
[ 40.623522][ T146] ? netif_set_real_num_tx_queues+0x780/0x780
[ 40.624290][ T146] ? notifier_call_chain+0x90/0x160
[ 40.624957][ T146] ? netdev_upper_dev_unlink+0x114/0x180
[ 40.625686][ T146] ? __netdev_adjacent_dev_unlink_neighbour+0x30/0x30
[ 40.626421][ T146] ? mutex_is_locked+0x13/0x50
[ 40.627016][ T146] ? unregister_netdevice_queue+0xf2/0x240
[ 40.627663][ T146] unregister_netdevice_many.part.134+0x13/0x1b0
[ 40.628362][ T146] default_device_exit_batch+0x2d9/0x390
[ 40.628987][ T146] ? unregister_netdevice_many+0x40/0x40
[ 40.629615][ T146] ? dev_change_net_namespace+0xcb0/0xcb0
[ 40.630279][ T146] ? prepare_to_wait_exclusive+0x2e0/0x2e0
[ 40.630943][ T146] ? ops_exit_list.isra.9+0x97/0x140
[ 40.631554][ T146] cleanup_net+0x441/0x890
[ ... ]
Fixes: e289fd28176b ("macvlan: fix the problem when mac address changes for passthru mode")
Reported-by: syzbot+5035b1f9dc7ea4558d5a@syzkaller.appspotmail.com
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 468f8f8e9eab71dc620375ee14c0a1f229845aea
Author: Taehee Yoo <ap420073@gmail.com>
Date: Thu Apr 23 13:40:47 2020 +0000
macsec: avoid to set wrong mtu
[ Upstream commit 7f327080364abccf923fa5a5b24e038eb0ba1407 ]
When a macsec interface is created, the mtu is calculated with the lower
interface's mtu value.
If the mtu of lower interface is lower than the length, which is needed
by macsec interface, macsec's mtu value will be overflowed.
So, if the lower interface's mtu is too low, macsec interface's mtu
should be set to 0.
Test commands:
ip link add dummy0 mtu 10 type dummy
ip link add macsec0 link dummy0 type macsec
ip link show macsec0
Before:
11: macsec0@dummy0: <BROADCAST,MULTICAST,M-DOWN> mtu 4294967274
After:
11: macsec0@dummy0: <BROADCAST,MULTICAST,M-DOWN> mtu 0
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 387e87973d0d10b5f0025d45c27b39d2a7c1dd55
Author: John Haxby <john.haxby@oracle.com>
Date: Sat Apr 18 16:30:49 2020 +0100
ipv6: fix restrict IPV6_ADDRFORM operation
[ Upstream commit 82c9ae440857840c56e05d4fb1427ee032531346 ]
Commit b6f6118901d1 ("ipv6: restrict IPV6_ADDRFORM operation") fixed a
problem found by syzbot an unfortunate logic error meant that it
also broke IPV6_ADDRFORM.
Rearrange the checks so that the earlier test is just one of the series
of checks made before moving the socket from IPv6 to IPv4.
Fixes: b6f6118901d1 ("ipv6: restrict IPV6_ADDRFORM operation")
Signed-off-by: John Haxby <john.haxby@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77dc1af082654557ba5168984e2ec0a3e6be2f70
Author: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Date: Mon Apr 20 15:26:54 2020 +0530
cxgb4: fix large delays in PTP synchronization
[ Upstream commit bd019427bf3623ee3c7d2845cf921bbf4c14846c ]
Fetching PTP sync information from mailbox is slow and can take
up to 10 milliseconds. Reduce this unnecessary delay by directly
reading the information from the corresponding registers.
Fixes: 9c33e4208bce ("cxgb4: Add PTP Hardware Clock (PHC) support")
Signed-off-by: Manoj Malviya <manojmalviya@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 953236ee91a99e8f63e200aedad07c9eff0bb6fc
Author: Vishal Kulkarni <vishal@chelsio.com>
Date: Wed Apr 22 21:20:07 2020 +0530
cxgb4: fix adapter crash due to wrong MC size
[ Upstream commit ce222748078592afb51b810dc154531aeba4f512 ]
In the absence of MC1, the size calculation function
cudbg_mem_region_size() was returing wrong MC size and
resulted in adapter crash. This patch adds new argument
to cudbg_mem_region_size() which will have actual size
and returns error to caller in the absence of MC1.
Fixes: a1c69520f785 ("cxgb4: collect MC memory dump")
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c434092ef8172ed027f2bd9afcd42c0ee5002b85
Author: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Date: Fri Dec 6 15:36:12 2019 +0000
x86/KVM: Clean up host's steal time structure
commit a6bd811f1209fe1c64c9f6fd578101d6436c6b6e upstream.
Now that we are mapping kvm_steal_time from the guest directly we
don't need keep a copy of it in kvm_vcpu_arch.st. The same is true
for the stime field.
This is part of CVE-2019-3016.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b5b79c757e6f22f17d8ddf2979abb7bf231bb327
Author: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Date: Thu Dec 5 03:45:32 2019 +0000
x86/KVM: Make sure KVM_VCPU_FLUSH_TLB flag is not missed
commit b043138246a41064527cf019a3d51d9f015e9796 upstream.
There is a potential race in record_steal_time() between setting
host-local vcpu->arch.st.steal.preempted to zero (i.e. clearing
KVM_VCPU_PREEMPTED) and propagating this value to the guest with
kvm_write_guest_cached(). Between those two events the guest may
still see KVM_VCPU_PREEMPTED in its copy of kvm_steal_time, set
KVM_VCPU_FLUSH_TLB and assume that hypervisor will do the right
thing. Which it won't.
Instad of copying, we should map kvm_steal_time and that will
guarantee atomicity of accesses to @preempted.
This is part of CVE-2019-3016.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 4.19: No tracepoint in record_steal_time().]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ccfc73e56da7c8e68ab6a543c5b8cd0b83c9e9bb
Author: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Date: Thu Dec 5 01:30:51 2019 +0000
x86/kvm: Cache gfn to pfn translation
commit 917248144db5d7320655dbb41d3af0b8a0f3d589 upstream.
__kvm_map_gfn()'s call to gfn_to_pfn_memslot() is
* relatively expensive
* in certain cases (such as when done from atomic context) cannot be called
Stashing gfn-to-pfn mapping should help with both cases.
This is part of CVE-2019-3016.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e36d68ec5090599058650152547d4a58ef3d79a0
Author: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Date: Tue Nov 12 16:35:06 2019 +0000
x86/kvm: Introduce kvm_(un)map_gfn()
commit 1eff70a9abd46f175defafd29bc17ad456f398a7 upstream.
kvm_vcpu_(un)map operates on gfns from any current address space.
In certain cases we want to make sure we are not mapping SMRAM
and for that we can use kvm_(un)map_gfn() that we are introducing
in this patch.
This is part of CVE-2019-3016.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ec81ed2fba221b8bb92b8010e82d92e1de3b39fa
Author: KarimAllah Ahmed <karahmed@amazon.de>
Date: Wed Jul 10 11:13:13 2019 +0200
KVM: Properly check if "page" is valid in kvm_vcpu_unmap
commit b614c6027896ff9ad6757122e84760d938cab15e upstream.
The field "page" is initialized to KVM_UNMAPPED_PAGE when it is not used
(i.e. when the memory lives outside kernel control). So this check will
always end up using kunmap even for memremap regions.
Fixes: e45adf665a53 ("KVM: Introduce a new guest mapping API")
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e25441275142a0d57a51025213c4b6ef17b193e6
Author: Christian Borntraeger <borntraeger@de.ibm.com>
Date: Mon May 27 10:28:25 2019 +0200
kvm: fix compile on s390 part 2
commit eb1f2f387db8c0d084581fb26e7faffde700bc8e upstream.
We also need to fence the memunmap part.
Fixes: e45adf665a53 ("KVM: Introduce a new guest mapping API")
Fixes: d30b214d1d0a (kvm: fix compilation on s390)
Cc: Michal Kubecek <mkubecek@suse.cz>
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bef6507903d91be2d1a06c11d980a722b176bc09
Author: Paolo Bonzini <pbonzini@redhat.com>
Date: Mon May 20 12:06:36 2019 +0200
kvm: fix compilation on s390
commit d30b214d1d0addb7b2c9c78178d1501cd39a01fb upstream.
s390 does not have memremap, even though in this particular case it
would be useful.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 94659e93c93c23dfaada78aaad45183867698f74
Author: Paolo Bonzini <pbonzini@redhat.com>
Date: Fri May 17 14:08:53 2019 +0200
kvm: fix compilation on aarch64
commit c011d23ba046826ccf8c4a4a6c1d01c9ccaa1403 upstream.
Commit e45adf665a53 ("KVM: Introduce a new guest mapping API", 2019-01-31)
introduced a build failure on aarch64 defconfig:
$ make -j$(nproc) ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- O=out defconfig \
Image.gz
...
../arch/arm64/kvm/../../../virt/kvm/kvm_main.c:
In function '__kvm_map_gfn':
../arch/arm64/kvm/../../../virt/kvm/kvm_main.c:1763:9: error:
implicit declaration of function 'memremap'; did you mean 'memset_p'?
../arch/arm64/kvm/../../../virt/kvm/kvm_main.c:1763:46: error:
'MEMREMAP_WB' undeclared (first use in this function)
../arch/arm64/kvm/../../../virt/kvm/kvm_main.c:
In function 'kvm_vcpu_unmap':
../arch/arm64/kvm/../../../virt/kvm/kvm_main.c:1795:3: error:
implicit declaration of function 'memunmap'; did you mean 'vm_munmap'?
because these functions are declared in <linux/io.h> rather than <asm/io.h>,
and the former was being pulled in already on x86 but not on aarch64.
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 4.19: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0125ed16a990014e27001f72fe75ad567da45f87
Author: KarimAllah Ahmed <karahmed@amazon.de>
Date: Thu Jan 31 21:24:34 2019 +0100
KVM: Introduce a new guest mapping API
commit e45adf665a53df0db37f784ed87c6b57ddd81885 upstream.
In KVM, specially for nested guests, there is a dominant pattern of:
=> map guest memory -> do_something -> unmap guest memory
In addition to all this unnecessarily noise in the code due to boiler plate
code, most of the time the mapping function does not properly handle memory
that is not backed by "struct page". This new guest mapping API encapsulate
most of this boiler plate code and also handles guest memory that is not
backed by "struct page".
The current implementation of this API is using memremap for memory that is
not backed by a "struct page" which would lead to a huge slow-down if it
was used for high-frequency mapping operations. The API does not have any
effect on current setups where guest memory is backed by a "struct page".
Further patches are going to also introduce a pfn-cache which would
significantly improve the performance of the memremap case.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 4.19 as dependency of commit 1eff70a9abd4
"x86/kvm: Introduce kvm_(un)map_gfn()"]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7570af489e73c55690d3666c360d0a6d56acdc12
Author: Sean Christopherson <sean.j.christopherson@intel.com>
Date: Tue May 7 09:06:28 2019 -0700
KVM: nVMX: Always sync GUEST_BNDCFGS when it comes from vmcs01
commit 3b013a2972d5bc344d6eaa8f24fdfe268211e45f upstream.
If L1 does not set VM_ENTRY_LOAD_BNDCFGS, then L1's BNDCFGS value must
be propagated to vmcs02 since KVM always runs with VM_ENTRY_LOAD_BNDCFGS
when MPX is supported. Because the value effectively comes from vmcs01,
vmcs02 must be updated even if vmcs12 is clean.
Fixes: 62cf9bd8118c4 ("KVM: nVMX: Fix emulation of VM_ENTRY_LOAD_BNDCFGS")
Cc: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 4.19: adjust filename, context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b4be98039a9224ec0cfc2b706e8e881b9ba53850
Author: Sean Christopherson <sean.j.christopherson@intel.com>
Date: Fri Jan 25 07:40:50 2019 -0800
KVM: VMX: Zero out *all* general purpose registers after VM-Exit
commit 0e0ab73c9a0243736bcd779b30b717e23ba9a56d upstream.
...except RSP, which is restored by hardware as part of VM-Exit.
Paolo theorized that restoring registers from the stack after a VM-Exit
in lieu of zeroing them could lead to speculative execution with the
guest's values, e.g. if the stack accesses miss the L1 cache[1].
Zeroing XORs are dirt cheap, so just be ultra-paranoid.
Note that the scratch register (currently RCX) used to save/restore the
guest state is also zeroed as its host-defined value is loaded via the
stack, just with a MOV instead of a POP.
[1] https://patchwork.kernel.org/patch/10771539/#22441255
Fixes: 0cb5b30698fd ("kvm: vmx: Scrub hardware GPRs at VM-exit")
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 4.19: adjust filename, context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ed523cbd4a6594edf123dc03ec9d70ea4f793671
Author: Randall Huang <huangrandall@google.com>
Date: Fri Oct 18 14:56:22 2019 +0800
f2fs: fix to avoid memory leakage in f2fs_listxattr
commit 688078e7f36c293dae25b338ddc9e0a2790f6e06 upstream.
In f2fs_listxattr, there is no boundary check before
memcpy e_name to buffer.
If the e_name_len is corrupted,
unexpected memory contents may be returned to the buffer.
Signed-off-by: Randall Huang <huangrandall@google.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
[bwh: Backported to 4.19: Use f2fs_msg() instead of f2fs_err()]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6d1444dbf949f78af996a044d39838b1a8d8de3d
Author: Cengiz Can <cengiz@kernel.wtf>
Date: Wed Mar 4 13:58:19 2020 +0300
blktrace: fix dereference after null check
commit 153031a301bb07194e9c37466cfce8eacb977621 upstream.
There was a recent change in blktrace.c that added a RCU protection to
`q->blk_trace` in order to fix a use-after-free issue during access.
However the change missed an edge case that can lead to dereferencing of
`bt` pointer even when it's NULL:
Coverity static analyzer marked this as a FORWARD_NULL issue with CID
1460458.
```
/kernel/trace/blktrace.c: 1904 in sysfs_blk_trace_attr_store()
1898 ret = 0;
1899 if (bt == NULL)
1900 ret = blk_trace_setup_queue(q, bdev);
1901
1902 if (ret == 0) {
1903 if (attr == &dev_attr_act_mask)
>>> CID 1460458: Null pointer dereferences (FORWARD_NULL)
>>> Dereferencing null pointer "bt".
1904 bt->act_mask = value;
1905 else if (attr == &dev_attr_pid)
1906 bt->pid = value;
1907 else if (attr == &dev_attr_start_lba)
1908 bt->start_lba = value;
1909 else if (attr == &dev_attr_end_lba)
```
Added a reassignment with RCU annotation to fix the issue.
Fixes: c780e86dd48 ("blktrace: Protect q->blk_trace with RCU")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bob Liu <bob.liu@oracle.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Cengiz Can <cengiz@kernel.wtf>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 473d7f5ed75b8c3750f0c6b442c8e23090d6da8f
Author: Jan Kara <jack@suse.cz>
Date: Thu Feb 6 15:28:12 2020 +0100
blktrace: Protect q->blk_trace with RCU
commit c780e86dd48ef6467a1146cf7d0fe1e05a635039 upstream.
KASAN is reporting that __blk_add_trace() has a use-after-free issue
when accessing q->blk_trace. Indeed the switching of block tracing (and
thus eventual freeing of q->blk_trace) is completely unsynchronized with
the currently running tracing and thus it can happen that the blk_trace
structure is being freed just while __blk_add_trace() works on it.
Protect accesses to q->blk_trace by RCU during tracing and make sure we
wait for the end of RCU grace period when shutting down tracing. Luckily
that is rare enough event that we can afford that. Note that postponing
the freeing of blk_trace to an RCU callback should better be avoided as
it could have unexpected user visible side-effects as debugfs files
would be still existing for a short while block tracing has been shut
down.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205711
CC: stable@vger.kernel.org
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reported-by: Tristan Madani <tristmd@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[bwh: Backported to 4.19: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5dd6835278454a7c7a045462253625de7c16b13e
Author: Sabrina Dubroca <sd@queasysnail.net>
Date: Wed Dec 4 15:35:53 2019 +0100
net: ipv6_stub: use ip6_dst_lookup_flow instead of ip6_dst_lookup
commit 6c8991f41546c3c472503dff1ea9daaddf9331c2 upstream.
ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.
All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().
This requires some changes in all the callers, as these two functions
take different arguments and have different return types.
Fixes: 5f81bd2e5d80 ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 4.19:
- Drop change in lwt_bpf.c
- Delete now-unused "ret" in mlx5e_route_lookup_ipv6()
- Initialise "out_dev" in mlx5e_create_encap_header_ipv6() to avoid
introducing a spurious "may be used uninitialised" warning
- Adjust filenames, context, indentation]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit abee5ded9bdb23946348c310245cb25c08240185
Author: Sabrina Dubroca <sd@queasysnail.net>
Date: Wed Dec 4 15:35:52 2019 +0100
net: ipv6: add net argument to ip6_dst_lookup_flow
commit c4e85f73afb6384123e5ef1bba3315b2e3ad031e upstream.
This will be used in the conversion of ipv6_stub to ip6_dst_lookup_flow,
as some modules currently pass a net argument without a socket to
ip6_dst_lookup. This is equivalent to commit 343d60aada5a ("ipv6: change
ipv6_stub_impl.ipv6_dst_lookup to take net argument").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 4.19: adjust context]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 58bcfc81c60a2ad85cbf01fba472a53cf9afb25b
Author: Heiner Kallweit <hkallweit1@gmail.com>
Date: Sat Oct 5 14:03:57 2019 +0200
PCI/ASPM: Allow re-enabling Clock PM
[ Upstream commit 35efea32b26f9aacc99bf07e0d2cdfba2028b099 ]
Previously Clock PM could not be re-enabled after being disabled by
pci_disable_link_state() because clkpm_capable was reset. Change this by
adding a clkpm_disable field similar to aspm_disable.
Link: https://lore.kernel.org/r/4e8a66db-7d53-4a66-c26c-f0037ffaa705@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8b1ab979c63d5077adc25ffd4a3c61d0133bf848
Author: Murthy Bhat <Murthy.Bhat@microsemi.com>
Date: Mon Oct 7 17:31:28 2019 -0500
scsi: smartpqi: fix call trace in device discovery
[ Upstream commit b969261134c1b990b96ea98fe5e0fcf8ec937c04 ]
Use sas_phy_delete rather than sas_phy_free which, according to
comments, should not be called for PHYs that have been set up
successfully.
Link: https://lore.kernel.org/r/157048748876.11757.17773443136670011786.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Murthy Bhat <Murthy.Bhat@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7231917fa7dbe478d1f65aaa482a3a0c70546c88
Author: Halil Pasic <pasic@linux.ibm.com>
Date: Thu Feb 13 13:37:28 2020 +0100
virtio-blk: improve virtqueue error to BLK_STS
[ Upstream commit 3d973b2e9a625996ee997c7303cd793b9d197c65 ]
Let's change the mapping between virtqueue_add errors to BLK_STS
statuses, so that -ENOSPC, which indicates virtqueue full is still
mapped to BLK_STS_DEV_RESOURCE, but -ENOMEM which indicates non-device
specific resource outage is mapped to BLK_STS_RESOURCE.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Link: https://lore.kernel.org/r/20200213123728.61216-3-pasic@linux.ibm.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7ad65e34ad1026a1389171c0a8d963d22739934a
Author: Steven Rostedt (VMware) <rostedt@goodmis.org>
Date: Wed Nov 13 11:48:39 2019 -0500
tracing/selftests: Turn off timeout setting
[ Upstream commit b43e78f65b1d35fd3e13c7b23f9b64ea83c9ad3a ]
As the ftrace selftests can run for a long period of time, disable the
timeout that the general selftests have. If a selftest hangs, then it
probably means the machine will hang too.
Link: https://lore.kernel.org/r/alpine.LSU.2.21.1911131604170.18679@pobox.suse.cz
Suggested-by: Miroslav Benes <mbenes@suse.cz>
Tested-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit de32c6ad7a4fcb986e0e4f39d7497948b734b8c7
Author: Yongqiang Sun <yongqiang.sun@amd.com>
Date: Mon Mar 9 17:13:02 2020 -0400
drm/amd/display: Not doing optimize bandwidth if flip pending.
[ Upstream commit 9941b8129030c9202aaf39114477a0e58c0d6ffc ]
[Why]
In some scenario like 1366x768 VSR enabled connected with a 4K monitor
and playing 4K video in clone mode, underflow will be observed due to
decrease dppclk when previouse surface scan isn't finished
[How]
In this use case, surface flip is switching between 4K and 1366x768,
1366x768 needs smaller dppclk, and when decrease the clk and previous
surface scan is for 4K and scan isn't done, underflow will happen. Not
doing optimize bandwidth in case of flip pending.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit af40b3eadbfb6e75c5f55d2cd5966a42161351a3
Author: Kai-Heng Feng <kai.heng.feng@canonical.com>
Date: Thu Mar 12 16:45:14 2020 +0200
xhci: Ensure link state is U3 after setting USB_SS_PORT_LS_U3
[ Upstream commit eb002726fac7cefb98ff39ddb89e150a1c24fe85 ]
The xHCI spec doesn't specify the upper bound of U3 transition time. For
some devices 20ms is not enough, so we need to make sure the link state
is in U3 before further actions.
I've tried to use U3 Entry Capability by setting U3 Entry Enable in
config register, however the port change event for U3 transition
interrupts the system suspend process.
For now let's use the less ideal method by polling PLS.
[use usleep_range(), and shorten the delay time while polling -Mathias]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d4dbc44bfa60d000d2f6209351382eb32097773f
Author: Hans de Goede <hdegoede@redhat.com>
Date: Sun Apr 5 15:37:26 2020 +0200
ASoC: Intel: bytcr_rt5640: Add quirk for MPMAN MPWIN895CL tablet
[ Upstream commit c8b78f24c1247b7bd0882885c672d9dec5800bc6 ]
The MPMAN MPWIN895CL tablet almost fully works with out default settings.
The only problem is that it has only 1 speaker so any sounds only playing
on the right channel get lost.
Add a quirk for this model using the default settings + MONO_SPEAKER.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200405133726.24154-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0cb5f1e1a019d6fd753137e8bc35e3e9b25cf30d
Author: Jiri Olsa <jolsa@kernel.org>
Date: Tue Apr 7 16:14:27 2020 +0200
perf/core: Disable page faults when getting phys address
[ Upstream commit d3296fb372bf7497b0e5d0478c4e7a677ec6f6e9 ]
We hit following warning when running tests on kernel
compiled with CONFIG_DEBUG_ATOMIC_SLEEP=y:
WARNING: CPU: 19 PID: 4472 at mm/gup.c:2381 __get_user_pages_fast+0x1a4/0x200
CPU: 19 PID: 4472 Comm: dummy Not tainted 5.6.0-rc6+ #3
RIP: 0010:__get_user_pages_fast+0x1a4/0x200
...
Call Trace:
perf_prepare_sample+0xff1/0x1d90
perf_event_output_forward+0xe8/0x210
__perf_event_overflow+0x11a/0x310
__intel_pmu_pebs_event+0x657/0x850
intel_pmu_drain_pebs_nhm+0x7de/0x11d0
handle_pmi_common+0x1b2/0x650
intel_pmu_handle_irq+0x17b/0x370
perf_event_nmi_handler+0x40/0x60
nmi_handle+0x192/0x590
default_do_nmi+0x6d/0x150
do_nmi+0x2f9/0x3c0
nmi+0x8e/0xd7
While __get_user_pages_fast() is IRQ-safe, it calls access_ok(),
which warns on:
WARN_ON_ONCE(!in_task() && !pagefault_disabled())
Peter suggested disabling page faults around __get_user_pages_fast(),
which gets rid of the warning in access_ok() call.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20200407141427.3184722-1-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 597cb12c6a927f527c40c1875969a2497f8d2207
Author: Florian Fainelli <f.fainelli@gmail.com>
Date: Mon Feb 3 13:35:35 2020 -0800
pwm: bcm2835: Dynamically allocate base
[ Upstream commit 2c25b07e5ec119cab609e41407a1fb3fa61442f5 ]
The newer 2711 and 7211 chips have two PWM controllers and failure to
dynamically allocate the PWM base would prevent the second PWM
controller instance being probed for succeeding with an -EEXIST error
from alloc_pwms().
Fixes: e5a06dc5ac1f ("pwm: Add BCM2835 PWM driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0b03af5905fcd982ca3abc8ed321a442d7d05171
Author: Geert Uytterhoeven <geert+renesas@glider.be>
Date: Mon Mar 16 11:32:15 2020 +0100
pwm: renesas-tpu: Fix late Runtime PM enablement
[ Upstream commit d5a3c7a4536e1329a758e14340efd0e65252bd3d ]
Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should always be disabled after the removal of the
PWM chip, even if the latter failed.
Fixes: 99b82abb0a35b073 ("pwm: Add Renesas TPU PWM driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d59e5b00d5771d65ff084668535de0f23924fdab
Author: Nicholas Piggin <npiggin@gmail.com>
Date: Thu Apr 2 22:04:01 2020 +1000
Revert "powerpc/64: irq_work avoid interrupt when called with hardware irqs enabled"
[ Upstream commit abc3fce76adbdfa8f87272c784b388cd20b46049 ]
This reverts commit ebb37cf3ffd39fdb6ec5b07111f8bb2f11d92c5f.
That commit does not play well with soft-masked irq state
manipulations in idle, interrupt replay, and possibly others due to
tracing code sometimes using irq_work_queue (e.g., in
trace_hardirqs_on()). That can cause PACA_IRQ_DEC to become set when
it is not expected, and be ignored or cleared or cause warnings.
The net result seems to be missing an irq_work until the next timer
interrupt in the worst case which is usually not going to be noticed,
however it could be a long time if the tick is disabled, which is
against the spirit of irq_work and might cause real problems.
The idea is still solid, but it would need more work. It's not really
clear if it would be worth added complexity, so revert this for
now (not a straight revert, but replace with a comment explaining why
we might see interrupts happening, and gives git blame something to
find).
Fixes: ebb37cf3ffd3 ("powerpc/64: irq_work avoid interrupt when called with hardware irqs enabled")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200402120401.1115883-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 012fd9ffcdf29b8a15f0de36677ebfa63920243c
Author: Evan Green <evgreen@chromium.org>
Date: Fri Apr 3 16:43:04 2020 +0200
loop: Better discard support for block devices
[ Upstream commit c52abf563049e787c1341cdf15c7dbe1bfbc951b ]
If the backing device for a loop device is itself a block device,
then mirror the "write zeroes" capabilities of the underlying
block device into the loop device. Copy this capability into both
max_write_zeroes_sectors and max_discard_sectors of the loop device.
The reason for this is that REQ_OP_DISCARD on a loop device translates
into blkdev_issue_zeroout(), rather than blkdev_issue_discard(). This
presents a consistent interface for loop devices (that discarded data
is zeroed), regardless of the backing device type of the loop device.
There should be no behavior change for loop devices backed by regular
files.
This change fixes blktest block/003, and removes an extraneous
error print in block/013 when testing on a loop device backed
by a block device that does not support discard.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
[used updated version of Evan's comment in loop_config_discard()]
[moved backingq to local scope, removed redundant braces]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 04727e685a331160c63b74cf6116b33695d32486
Author: Cornelia Huck <cohuck@redhat.com>
Date: Fri Mar 27 13:45:02 2020 +0100
s390/cio: avoid duplicated 'ADD' uevents
[ Upstream commit 05ce3e53f375295c2940390b2b429e506e07655c ]
The common I/O layer delays the ADD uevent for subchannels and
delegates generating this uevent to the individual subchannel
drivers. The io_subchannel driver will do so when the associated
ccw_device has been registered -- but unconditionally, so more
ADD uevents will be generated if a subchannel has been unbound
from the io_subchannel driver and later rebound.
To fix this, only generate the ADD event if uevents were still
suppressed for the device.
Fixes: fa1a8c23eb7d ("s390: cio: Delay uevents for subchannels")
Message-Id: <20200327124503.9794-2-cohuck@redhat.com>
Reported-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7667fd8e5bb0640417cb3a393f96232a463808a4
Author: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Date: Thu Apr 2 11:28:03 2020 +0200
kconfig: qconf: Fix a few alignment issues
[ Upstream commit 60969f02f07ae1445730c7b293c421d179da729c ]
There are a few items with wrong alignments. Solve them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cb0ab2beb9c7bd352813f365bb1a73527579b416
Author: Vasily Averin <vvs@virtuozzo.com>
Date: Fri Apr 10 14:34:13 2020 -0700
ipc/util.c: sysvipc_find_ipc() should increase position index
[ Upstream commit 89163f93c6f969da5811af5377cc10173583123b ]
If seq_file .next function does not change position index, read after
some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Waiman Long <longman@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: NeilBrown <neilb@suse.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/b7a20945-e315-8bb0-21e6-3875c14a8494@virtuozzo.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 550d3bc535e0d22eb90dbd91452874299203ca43
Author: Eric Biggers <ebiggers@google.com>
Date: Fri Apr 10 14:33:53 2020 -0700
selftests: kmod: fix handling test numbers above 9
[ Upstream commit 6d573a07528308eb77ec072c010819c359bebf6e ]
get_test_count() and get_test_enabled() were broken for test numbers
above 9 due to awk interpreting a field specification like '$0010' as
octal rather than decimal. Fix it by stripping the leading zeroes.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jeff Vander Stoep <jeffv@google.com>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: NeilBrown <neilb@suse.com>
Link: http://lkml.kernel.org/r/20200318230515.171692-5-ebiggers@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 99e811d8d737fb3e107924d65cecb8368271421e
Author: Vasily Averin <vvs@virtuozzo.com>
Date: Fri Apr 10 14:34:10 2020 -0700
kernel/gcov/fs.c: gcov_seq_next() should increase position index
[ Upstream commit f4d74ef6220c1eda0875da30457bef5c7111ab06 ]
If seq_file .next function does not change position index, read after
some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: NeilBrown <neilb@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Waiman Long <longman@redhat.com>
Link: http://lkml.kernel.org/r/f65c6ee7-bd00-f910-2f8a-37cc67e4ff88@virtuozzo.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b15eafb3f928a6d4717d828701f15e1e8bf19da7
Author: Sagi Grimberg <sagi@grimberg.me>
Date: Thu Apr 2 09:34:54 2020 -0700
nvme: fix deadlock caused by ANA update wrong locking
[ Upstream commit 657f1975e9d9c880fa13030e88ba6cc84964f1db ]
The deadlock combines 4 flows in parallel:
- ns scanning (triggered from reconnect)
- request timeout
- ANA update (triggered from reconnect)
- I/O coming into the mpath device
(1) ns scanning triggers disk revalidation -> update disk info ->
freeze queue -> but blocked, due to (2)
(2) timeout handler reference the g_usage_counter - > but blocks in
the transport .timeout() handler, due to (3)
(3) the transport timeout handler (indirectly) calls nvme_stop_queue() ->
which takes the (down_read) namespaces_rwsem - > but blocks, due to (4)
(4) ANA update takes the (down_write) namespaces_rwsem -> calls
nvme_mpath_set_live() -> which synchronize the ns_head srcu
(see commit 504db087aacc) -> but blocks, due to (5)
(5) I/O came into nvme_mpath_make_request -> took srcu_read_lock ->
direct_make_request > blk_queue_enter -> but blocked, due to (1)
==> the request queue is under freeze -> deadlock.
The fix is making ANA update take a read lock as the namespaces list
is not manipulated, it is just the ns and ns->head that are being
updated (which is protected with the ns->head lock).
Fixes: 0d0b660f214dc ("nvme: add ANA support")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b9b57d4d67a454eae688400c5d4db183c609d85f
Author: Hans de Goede <hdegoede@redhat.com>
Date: Thu Apr 2 20:53:57 2020 +0200
ASoC: Intel: atom: Take the drv->lock mutex before calling sst_send_slot_map()
[ Upstream commit 81630dc042af998b9f58cd8e2c29dab9777ea176 ]
sst_send_slot_map() uses sst_fill_and_send_cmd_unlocked() because in some
places it is called with the drv->lock mutex already held.
So it must always be called with the mutex locked. This commit adds missing
locking in the sst_set_be_modules() code-path.
Fixes: 24c8d14192cc ("ASoC: Intel: mrfld: add DSP core controls")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200402185359.3424-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8d1eb1fbdb350575987cfb28ed7715999c1a783e
Author: Wu Bo <wubo40@huawei.com>
Date: Tue Mar 24 15:58:50 2020 +0800
scsi: iscsi: Report unbind session event when the target has been removed
[ Upstream commit 13e60d3ba287d96eeaf1deaadba51f71578119a3 ]
If the daemon is restarted or crashes while logging out of a session, the
unbind session event sent by the kernel is not processed and is lost. When
the daemon starts again, the session can't be unbound because the daemon is
waiting for the event message. However, the kernel has already logged out
and the event will not be resent.
When iscsid restart is complete, logout session reports error:
Logging out of session [sid: 6, target: iqn.xxxxx, portal: xx.xx.xx.xx,3260]
iscsiadm: Could not logout of [sid: 6, target: iscsiadm -m node iqn.xxxxx, portal: xx.xx.xx.xx,3260].
iscsiadm: initiator reported error (9 - internal error)
iscsiadm: Could not logout of all requested sessions
Make sure the unbind event is emitted.
[mkp: commit desc and applied by hand since patch was mangled]
Link: https://lore.kernel.org/r/4eab1771-2cb3-8e79-b31c-923652340e99@huawei.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Wu Bo <wubo40@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b12c28eccfc597b4d271ef37280c58f173b0026f
Author: Geert Uytterhoeven <geert+renesas@glider.be>
Date: Mon Mar 16 11:32:14 2020 +0100
pwm: rcar: Fix late Runtime PM enablement
[ Upstream commit 1451a3eed24b5fd6a604683f0b6995e0e7e16c79 ]
Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should be disabled after the removal of the PWM
chip.
Fixes: ed6c1476bf7f16d5 ("pwm: Add support for R-Car PWM Timer")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2ebb10f20ac8811ebd5ff08744c863ea41828e83
Author: Yan, Zheng <zyan@redhat.com>
Date: Tue Mar 10 19:34:20 2020 +0800
ceph: don't skip updating wanted caps when cap is stale
[ Upstream commit 0aa971b6fd3f92afef6afe24ef78d9bb14471519 ]
1. try_get_cap_refs() fails to get caps and finds that mds_wanted
does not include what it wants. It returns -ESTALE.
2. ceph_get_caps() calls ceph_renew_caps(). ceph_renew_caps() finds
that inode has cap, so it calls ceph_check_caps().
3. ceph_check_caps() finds that issued caps (without checking if it's
stale) already includes caps wanted by open file, so it skips
updating wanted caps.
Above events can cause an infinite loop inside ceph_get_caps().
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a7eba547137b9e699cea0d363ec2e31c5ef5f281
Author: Qiujun Huang <hqjagain@gmail.com>
Date: Fri Mar 6 09:34:20 2020 +0800
ceph: return ceph_mdsc_do_request() errors from __get_parent()
[ Upstream commit c6d50296032f0b97473eb2e274dc7cc5d0173847 ]
Return the error returned by ceph_mdsc_do_request(). Otherwise,
r_target_inode ends up being NULL this ends up returning ENOENT
regardless of the error.
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b77e19da5647ebec0e3306cb47942ede0cfd079c
Author: James Smart <jsmart2021@gmail.com>
Date: Sun Mar 22 11:12:59 2020 -0700
scsi: lpfc: Fix crash in target side cable pulls hitting WAIT_FOR_UNREG
[ Upstream commit 807e7353d8a7105ce884d22b0dbc034993c6679c ]
Kernel is crashing with the following stacktrace:
BUG: unable to handle kernel NULL pointer dereference at
00000000000005bc
IP: lpfc_nvme_register_port+0x1a8/0x3a0 [lpfc]
...
Call Trace:
lpfc_nlp_state_cleanup+0x2b2/0x500 [lpfc]
lpfc_nlp_set_state+0xd7/0x1a0 [lpfc]
lpfc_cmpl_prli_prli_issue+0x1f7/0x450 [lpfc]
lpfc_disc_state_machine+0x7a/0x1e0 [lpfc]
lpfc_cmpl_els_prli+0x16f/0x1e0 [lpfc]
lpfc_sli_sp_handle_rspiocb+0x5b2/0x690 [lpfc]
lpfc_sli_handle_slow_ring_event_s4+0x182/0x230 [lpfc]
lpfc_do_work+0x87f/0x1570 [lpfc]
kthread+0x10d/0x130
ret_from_fork+0x35/0x40
During target side fault injections, it is possible to hit the
NLP_WAIT_FOR_UNREG case in lpfc_nvme_remoteport_delete. A prior commit
fixed a rebind and delete race condition, but called lpfc_nlp_put
unconditionally. This triggered a deletion and the crash.
Fix by movng nlp_put to inside the NLP_WAIT_FOR_UNREG case, where the nlp
will be being unregistered/removed. Leave the reference if the flag isn't
set.
Link: https://lore.kernel.org/r/20200322181304.37655-8-jsmart2021@gmail.com
Fixes: b15bd3e6212e ("scsi: lpfc: Fix nvme remoteport registration race conditions")
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8fb312a0a9247375c708d60c60fe6980931fc8da
Author: James Smart <jsmart2021@gmail.com>
Date: Sun Mar 22 11:12:53 2020 -0700
scsi: lpfc: Fix kasan slab-out-of-bounds error in lpfc_unreg_login
[ Upstream commit 38503943c89f0bafd9e3742f63f872301d44cbea ]
The following kasan bug was called out:
BUG: KASAN: slab-out-of-bounds in lpfc_unreg_login+0x7c/0xc0 [lpfc]
Read of size 2 at addr ffff889fc7c50a22 by task lpfc_worker_3/6676
...
Call Trace:
dump_stack+0x96/0xe0
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
print_address_description.constprop.6+0x1b/0x220
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
__kasan_report.cold.9+0x37/0x7c
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
kasan_report+0xe/0x20
lpfc_unreg_login+0x7c/0xc0 [lpfc]
lpfc_sli_def_mbox_cmpl+0x334/0x430 [lpfc]
...
When processing the completion of a "Reg Rpi" login mailbox command in
lpfc_sli_def_mbox_cmpl, a call may be made to lpfc_unreg_login. The vpi is
extracted from the completing mailbox context and passed as an input for
the next. However, the vpi stored in the mailbox command context is an
absolute vpi, which for SLI4 represents both base + offset. When used with
a non-zero base component, (function id > 0) this results in an
out-of-range access beyond the allocated phba->vpi_ids array.
Fix by subtracting the function's base value to get an accurate vpi number.
Link: https://lore.kernel.org/r/20200322181304.37655-2-jsmart2021@gmail.com
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ba54ddabc0135481eff2f380d424a2228d347008
Author: Tero Kristo <t-kristo@ti.com>
Date: Thu Mar 12 11:58:06 2020 +0200
watchdog: reset last_hw_keepalive time at start
[ Upstream commit 982bb70517aef2225bad1d802887b733db492cc0 ]
Currently the watchdog core does not initialize the last_hw_keepalive
time during watchdog startup. This will cause the watchdog to be pinged
immediately if enough time has passed from the system boot-up time, and
some types of watchdogs like K3 RTI does not like this.
To avoid the issue, setup the last_hw_keepalive time during watchdog
startup.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200302200426.6492-3-t-kristo@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d42f91ba29e3d8b76ac7136751e0e88ddca025ed
Author: Catalin Marinas <catalin.marinas@arm.com>
Date: Fri Apr 24 17:38:45 2020 +0100
arm64: Silence clang warning on mismatched value/register sizes
[ Upstream commit: 27a22fbdeedd6c5c451cf5f830d51782bf50c3a2 ]
Clang reports a warning on the __tlbi(aside1is, 0) macro expansion since
the value size does not match the register size specified in the inline
asm. Construct the ASID value using the __TLBI_VADDR() macro.
Fixes: 222fc0c8503d ("arm64: compat: Workaround Neoverse-N1 #1542419 for compat user-space")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 05a5ec4131b747b57c268cb72c6810ef6a8e653f
Author: James Morse <james.morse@arm.com>
Date: Fri Apr 24 17:38:44 2020 +0100
arm64: compat: Workaround Neoverse-N1 #1542419 for compat user-space
[ Upstream commit: 222fc0c8503d98cec3cb2bac2780cdd21a6e31c0 ]
Compat user-space is unable to perform ICIMVAU instructions from
user-space. Instead it uses a compat-syscall. Add the workaround for
Neoverse-N1 #1542419 to this code path.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0cfa7fbc564e1d4fe3fadf0179ab99b3bf0b32bb
Author: James Morse <james.morse@arm.com>
Date: Fri Apr 24 17:38:43 2020 +0100
arm64: Fake the IminLine size on systems affected by Neoverse-N1 #1542419
[ Upstream commit ee9d90be9ddace01b7fb126567e4b539fbe1f82f ]
Systems affected by Neoverse-N1 #1542419 support DIC so do not need to
perform icache maintenance once new instructions are cleaned to the PoU.
For the errata workaround, the kernel hides DIC from user-space, so that
the unnecessary cache maintenance can be trapped by firmware.
To reduce the number of traps, produce a fake IminLine value based on
PAGE_SIZE.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1b568dfec3124e03e1d6000d5d311b11492682ed
Author: James Morse <james.morse@arm.com>
Date: Fri Apr 24 17:38:42 2020 +0100
arm64: errata: Hide CTR_EL0.DIC on systems affected by Neoverse-N1 #1542419
[ Upstream commit 05460849c3b51180d5ada3373d0449aea19075e4 ]
Cores affected by Neoverse-N1 #1542419 could execute a stale instruction
when a branch is updated to point to freshly generated instructions.
To workaround this issue we need user-space to issue unnecessary
icache maintenance that we can trap. Start by hiding CTR_EL0.DIC.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[ Removed cpu_enable_trap_ctr_access() hunk due to no 4afe8e79da92]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4355296b8d6235d1b3b2bcdd20b4242ce399a878
Author: Marc Zyngier <maz@kernel.org>
Date: Fri Apr 24 17:38:41 2020 +0100
arm64: Add part number for Neoverse N1
[ Upstream commit 0cf57b86859c49381addb3ce47be70aadf5fd2c0 ]
New CPU, new part number. You know the drill.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit be2b6b4a22013ce7016388b276a6a9b147bb0a24
Author: Jeremy Sowden <jeremy@azazel.net>
Date: Tue Mar 19 15:39:21 2019 +0000
vti4: removed duplicate log message.
commit 01ce31c57b3f07c91c9d45bbaf126124cce83a5d upstream.
Removed info log-message if ipip tunnel registration fails during
module-initialization: it adds nothing to the error message that is
written on all failures.
Fixes: dd9ee3444014e ("vti4: Fix a ipip packet processing bug in 'IPCOMP' virtual tunnel")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 259ea41f36044fd323a04aeca14ecd7b87797837
Author: Wei Yongjun <weiyongjun1@huawei.com>
Date: Thu Oct 11 01:49:48 2018 +0000
crypto: mxs-dcp - make symbols 'sha1_null_hash' and 'sha256_null_hash' static
commit ce4e45842de3eb54b8dd6e081765d741f5b92b56 upstream.
Fixes the following sparse warnings:
drivers/crypto/mxs-dcp.c:39:15: warning:
symbol 'sha1_null_hash' was not declared. Should it be static?
drivers/crypto/mxs-dcp.c:43:15: warning:
symbol 'sha256_null_hash' was not declared. Should it be static?
Fixes: c709eebaf5c5 ("crypto: mxs-dcp - Fix SHA null hashes and output length")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d6f9d8f3170c78e4817a0af673b3dc1d5b848ca
Author: Martin KaFai Lau <kafai@fb.com>
Date: Fri Jan 10 15:16:44 2020 -0800
bpftool: Fix printing incorrect pointer in btf_dump_ptr
commit 555089fdfc37ad65e0ee9b42ca40c238ff546f83 upstream.
For plain text output, it incorrectly prints the pointer value
"void *data". The "void *data" is actually pointing to memory that
contains a bpf-map's value. The intention is to print the content of
the bpf-map's value instead of printing the pointer pointing to the
bpf-map's value.
In this case, a member of the bpf-map's value is a pointer type.
Thus, it should print the "*(void **)data".
Fixes: 22c349e8db89 ("tools: bpftool: fix format strings and arguments for jsonw_printf()")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Link: https://lore.kernel.org/bpf/20200110231644.3484151-1-kafai@fb.com
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05fe33cad98588ac4026e7d5cd035ee36a4f8d62
Author: Rob Clark <robdclark@chromium.org>
Date: Wed Sep 4 09:56:03 2019 -0700
drm/msm: Use the correct dma_sync calls harder
commit 9f614197c744002f9968e82c649fdf7fe778e1e7 upstream.
Looks like the dma_sync calls don't do what we want on armv7 either.
Fixes:
Unable to handle kernel paging request at virtual address 50001000
pgd = (ptrval)
[50001000] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.3.0-rc6-00271-g9f159ae07f07 #4
Hardware name: Freescale i.MX53 (Device Tree Support)
PC is at v7_dma_clean_range+0x20/0x38
LR is at __dma_page_cpu_to_dev+0x28/0x90
pc : [<c011c76c>] lr : [<c01181c4>] psr: 20000013
sp : d80b5a88 ip : de96c000 fp : d840ce6c
r10: 00000000 r9 : 00000001 r8 : d843e010
r7 : 00000000 r6 : 00008000 r5 : ddb6c000 r4 : 00000000
r3 : 0000003f r2 : 00000040 r1 : 50008000 r0 : 50001000
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 70004019 DAC: 00000051
Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes: 3de433c5b38a ("drm/msm: Use the correct dma_sync calls in msm_gem")
Tested-by: Fabio Estevam <festevam@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b61c29e397e70a50116308fa9bc8ee173e60c74d
Author: Dmitry Monakhov <dmonakhov@gmail.com>
Date: Wed Nov 6 12:25:02 2019 +0000
ext4: fix extent_status fragmentation for plain files
[ Upstream commit 4068664e3cd2312610ceac05b74c4cf1853b8325 ]
Extents are cached in read_extent_tree_block(); as a result, extents
are not cached for inodes with depth == 0 when we try to find the
extent using ext4_find_extent(). The result of the lookup is cached
in ext4_map_blocks() but is only a subset of the extent on disk. As a
result, the contents of extents status cache can get very badly
fragmented for certain workloads, such as a random 4k read workload.
File size of /mnt/test is 33554432 (8192 blocks of 4096 bytes)
ext: logical_offset: physical_offset: length: expected: flags:
0: 0.. 8191: 40960.. 49151: 8192: last,eof
$ perf record -e 'ext4:ext4_es_*' /root/bin/fio --name=t --direct=0 --rw=randread --bs=4k --filesize=32M --size=32M --filename=/mnt/test
$ perf script | grep ext4_es_insert_extent | head -n 10
fio 131 [000] 13.975421: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [494/1) mapped 41454 status W
fio 131 [000] 13.975939: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [6064/1) mapped 47024 status W
fio 131 [000] 13.976467: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [6907/1) mapped 47867 status W
fio 131 [000] 13.976937: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [3850/1) mapped 44810 status W
fio 131 [000] 13.977440: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [3292/1) mapped 44252 status W
fio 131 [000] 13.977931: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [6882/1) mapped 47842 status W
fio 131 [000] 13.978376: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [3117/1) mapped 44077 status W
fio 131 [000] 13.978957: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [2896/1) mapped 43856 status W
fio 131 [000] 13.979474: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [7479/1) mapped 48439 status W
Fix this by caching the extents for inodes with depth == 0 in
ext4_find_extent().
[ Renamed ext4_es_cache_extents() to ext4_cache_extents() since this
newly added function is not in extents_cache.c, and to avoid
potential visual confusion with ext4_es_cache_extent(). -TYT ]
Signed-off-by: Dmitry Monakhov <dmonakhov@gmail.com>
Link: https://lore.kernel.org/r/20191106122502.19986-1-dmonakhov@gmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>