commit 206f91a12c5f69c9b4dfd4e0029043794a046933
Author: Sasha Levin <sasha.levin@oracle.com>
Date: Sun Apr 3 18:26:26 2016 -0400
Linux 4.1.21
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 919e67a63aa967566a909f4f6e1c13f8e88cf76e
Author: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Date: Thu Mar 24 11:14:53 2016 +0000
perf/core: Fix perf_sched_count derailment
[ Upstream commit 927a5570855836e5d5859a80ce7e91e963545e8f ]
The error path in perf_event_open() is such that asking for a sampling
event on a PMU that doesn't generate interrupts will end up in dropping
the perf_sched_count even though it hasn't been incremented for this
event yet.
Given a sufficient amount of these calls, we'll end up disabling
scheduler's jump label even though we'd still have active events in the
system, thereby facilitating the arrival of the infernal regions upon us.
I'm fixing this by moving account_event() inside perf_event_alloc().
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/1456917854-29427-1-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: He Kuang <hekuang@huawei.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 882f862db7f3509f055208b2e3e5bd263265a03b
Author: Peter Zijlstra <peterz@infradead.org>
Date: Thu Mar 24 11:14:52 2016 +0000
perf: Cure event->pending_disable race
[ Upstream commit 28a967c3a2f99fa3b5f762f25cb2a319d933571b ]
Because event_sched_out() checks event->pending_disable _before_
actually disabling the event, it can happen that the event fires after
it checks but before it gets disabled.
This would leave event->pending_disable set and the queued irq_work
will try and process it.
However, if the event trigger was during schedule(), the event might
have been de-scheduled by the time the irq_work runs, and
perf_event_disable_local() will fail.
Fix this by checking event->pending_disable _after_ we call
event->pmu->del(). This depends on the latter being a compiler
barrier, such that the compiler does not lift the load and re-creates
the problem.
Tested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dvyukov@google.com
Cc: eranian@google.com
Cc: oleg@redhat.com
Cc: panand@redhat.com
Cc: sasha.levin@oracle.com
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/20160224174948.040469884@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: He Kuang <hekuang@huawei.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 5709e7ba03717ab760b5ad6ebcf4a9e2f633dcc4
Author: Peter Zijlstra <peterz@infradead.org>
Date: Thu Mar 24 11:14:51 2016 +0000
perf: Do not double free
[ Upstream commit 130056275ade730e7a79c110212c8815202773ee ]
In case of: err_file: fput(event_file), we'll end up calling
perf_release() which in turn will free the event.
Do not then free the event _again_.
Tested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dvyukov@google.com
Cc: eranian@google.com
Cc: oleg@redhat.com
Cc: panand@redhat.com
Cc: sasha.levin@oracle.com
Cc: vince@deater.net
Link: http://lkml.kernel.org/r/20160224174947.697350349@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: He Kuang <hekuang@huawei.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 143cf26c48278bd438a97a8bd3e18b6460192981
Author: Yang Shi <yang.shi@linaro.org>
Date: Thu Mar 24 11:14:50 2016 +0000
arm64: replace read_lock to rcu lock in call_step_hook
[ Upstream commit cf0a25436f05753aca5151891aea4fd130556e2a ]
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917
in_atomic(): 1, irqs_disabled(): 128, pid: 383, name: sh
Preemption disabled at:[<ffff800000124c18>] kgdb_cpu_enter+0x158/0x6b8
CPU: 3 PID: 383 Comm: sh Tainted: G W 4.1.13-rt13 #2
Hardware name: Freescale Layerscape 2085a RDB Board (DT)
Call trace:
[<ffff8000000885e8>] dump_backtrace+0x0/0x128
[<ffff800000088734>] show_stack+0x24/0x30
[<ffff80000079a7c4>] dump_stack+0x80/0xa0
[<ffff8000000bd324>] ___might_sleep+0x18c/0x1a0
[<ffff8000007a20ac>] __rt_spin_lock+0x2c/0x40
[<ffff8000007a2268>] rt_read_lock+0x40/0x58
[<ffff800000085328>] single_step_handler+0x38/0xd8
[<ffff800000082368>] do_debug_exception+0x58/0xb8
Exception stack(0xffff80834a1e7c80 to 0xffff80834a1e7da0)
7c80: ffffff9c ffffffff 92c23ba0 0000ffff 4a1e7e40 ffff8083 001bfcc4 ffff8000
7ca0: f2000400 00000000 00000000 00000000 4a1e7d80 ffff8083 0049501c ffff8000
7cc0: 00005402 00000000 00aaa210 ffff8000 4a1e7ea0 ffff8083 000833f4 ffff8000
7ce0: ffffff9c ffffffff 92c23ba0 0000ffff 4a1e7ea0 ffff8083 001bfcc0 ffff8000
7d00: 4a0fc400 ffff8083 00005402 00000000 4a1e7d40 ffff8083 00490324 ffff8000
7d20: ffffff9c 00000000 92c23ba0 0000ffff 000a0000 00000000 00000000 00000000
7d40: 00000008 00000000 00080000 00000000 92c23b8b 0000ffff 92c23b8e 0000ffff
7d60: 00000038 00000000 00001cb2 00000000 00000005 00000000 92d7b498 0000ffff
7d80: 01010101 01010101 92be9000 0000ffff 00000000 00000000 00000030 00000000
[<ffff8000000833f4>] el1_dbg+0x18/0x6c
This issue is similar with 62c6c61("arm64: replace read_lock to rcu lock in
call_break_hook"), but comes to single_step_handler.
This also solves kgdbts boot test silent hang issue on 4.4 -rt kernel.
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: He Kuang <hekuang@huawei.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 1a138f3e487026aede3642cbe09aee0f64c2f66b
Author: Yang Shi <yang.shi@linaro.org>
Date: Thu Mar 24 11:14:49 2016 +0000
arm64: replace read_lock to rcu lock in call_break_hook
[ Upstream commit 62c6c61adbc623cdacf74b8f29c278e539060c48 ]
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917
in_atomic(): 0, irqs_disabled(): 128, pid: 342, name: perf
1 lock held by perf/342:
#0: (break_hook_lock){+.+...}, at: [<ffffffc0000851ac>] call_break_hook+0x34/0xd0
irq event stamp: 62224
hardirqs last enabled at (62223): [<ffffffc00010b7bc>] __call_rcu.constprop.59+0x104/0x270
hardirqs last disabled at (62224): [<ffffffc0000fbe20>] vprintk_emit+0x68/0x640
softirqs last enabled at (0): [<ffffffc000097928>] copy_process.part.8+0x428/0x17f8
softirqs last disabled at (0): [< (null)>] (null)
CPU: 0 PID: 342 Comm: perf Not tainted 4.1.6-rt5 #4
Hardware name: linux,dummy-virt (DT)
Call trace:
[<ffffffc000089968>] dump_backtrace+0x0/0x128
[<ffffffc000089ab0>] show_stack+0x20/0x30
[<ffffffc0007030d0>] dump_stack+0x7c/0xa0
[<ffffffc0000c878c>] ___might_sleep+0x174/0x260
[<ffffffc000708ac8>] __rt_spin_lock+0x28/0x40
[<ffffffc000708db0>] rt_read_lock+0x60/0x80
[<ffffffc0000851a8>] call_break_hook+0x30/0xd0
[<ffffffc000085a70>] brk_handler+0x30/0x98
[<ffffffc000082248>] do_debug_exception+0x50/0xb8
Exception stack(0xffffffc00514fe30 to 0xffffffc00514ff50)
fe20: 00000000 00000000 c1594680 0000007f
fe40: ffffffff ffffffff 92063940 0000007f 0550dcd8 ffffffc0 00000000 00000000
fe60: 0514fe70 ffffffc0 000be1f8 ffffffc0 0514feb0 ffffffc0 0008948c ffffffc0
fe80: 00000004 00000000 0514fed0 ffffffc0 ffffffff ffffffff 9282a948 0000007f
fea0: 00000000 00000000 9282b708 0000007f c1592820 0000007f 00083914 ffffffc0
fec0: 00000000 00000000 00000010 00000000 00000064 00000000 00000001 00000000
fee0: 005101e0 00000000 c1594680 0000007f c1594740 0000007f ffffffd8 ffffff80
ff00: 00000000 00000000 00000000 00000000 c1594770 0000007f c1594770 0000007f
ff20: 00665e10 00000000 7f7f7f7f 7f7f7f7f 01010101 01010101 00000000 00000000
ff40: 928e4cc0 0000007f 91ff11e8 0000007f
call_break_hook is called in atomic context (hard irq disabled), so replace
the sleepable lock to rcu lock, replace relevant list operations to rcu
version and call synchronize_rcu() in unregister_break_hook().
And, replace write lock to spinlock in {un}register_break_hook.
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: He Kuang <hekuang@huawei.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit f2b132595b89d9236b386e1d6ed3fcf5e9edf4cb
Author: Jan Kara <jack@suse.com>
Date: Mon Dec 7 14:34:49 2015 -0500
ext4: fix races of writeback with punch hole and zero range
When doing delayed allocation, update of on-disk inode size is postponed
until IO submission time. However hole punch or zero range fallocate
calls can end up discarding the tail page cache page and thus on-disk
inode size would never be properly updated.
Make sure the on-disk inode size is updated before truncating page
cache.
Signed-off-by: Jan Kara <jack@suse.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Mingming Cao <mingming.cao@oracle.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 181aaebde9360b8235df647ee36dafdc041d4964
Author: Jan Kara <jack@suse.com>
Date: Mon Dec 7 14:31:11 2015 -0500
ext4: fix races between buffered IO and collapse / insert range
Current code implementing FALLOC_FL_COLLAPSE_RANGE and
FALLOC_FL_INSERT_RANGE is prone to races with buffered writes and page
faults. If buffered write or write via mmap manages to squeeze between
filemap_write_and_wait_range() and truncate_pagecache() in the fallocate
implementations, the written data is simply discarded by
truncate_pagecache() although it should have been shifted.
Fix the problem by moving filemap_write_and_wait_range() call inside
i_mutex and i_mmap_sem. That way we are protected against races with
both buffered writes and page faults.
Signed-off-by: Jan Kara <jack@suse.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Mingming Cao <mingming.cao@oracle.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 9621787d69783fc23d14e1332377d7170d6928ed
Author: Jan Kara <jack@suse.com>
Date: Mon Dec 7 14:29:17 2015 -0500
ext4: move unlocked dio protection from ext4_alloc_file_blocks()
Currently ext4_alloc_file_blocks() was handling protection against
unlocked DIO. However we now need to sometimes call it under i_mmap_sem
and sometimes not and DIO protection ranks above it (although strictly
speaking this cannot currently create any deadlocks). Also
ext4_zero_range() was actually getting & releasing unlocked DIO
protection twice in some cases. Luckily it didn't introduce any real bug
but it was a land mine waiting to be stepped on. So move DIO protection
out from ext4_alloc_file_blocks() into the two callsites.
Signed-off-by: Jan Kara <jack@suse.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Mingming Cao <mingming.cao@oracle.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 248766f068fd1d3d95479f470bc926d1136141d6
Author: Jan Kara <jack@suse.com>
Date: Mon Dec 7 14:28:03 2015 -0500
ext4: fix races between page faults and hole punching
Currently, page faults and hole punching are completely unsynchronized.
This can result in page fault faulting in a page into a range that we
are punching after truncate_pagecache_range() has been called and thus
we can end up with a page mapped to disk blocks that will be shortly
freed. Filesystem corruption will shortly follow. Note that the same
race is avoided for truncate by checking page fault offset against
i_size but there isn't similar mechanism available for punching holes.
Fix the problem by creating new rw semaphore i_mmap_sem in inode and
grab it for writing over truncate, hole punching, and other functions
removing blocks from extent tree and for read over page faults. We
cannot easily use i_data_sem for this since that ranks below transaction
start and we need something ranking above it so that it can be held over
the whole truncate / hole punching operation. Also remove various
workarounds we had in the code to reduce race window when page fault
could have created pages with stale mapping information.
Signed-off-by: Jan Kara <jack@suse.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Mingming Cao <mingming.cao@oracle.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 14b4d1419ee6e71e672926d90a5bd87f698014d3
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Sun Mar 6 22:28:56 2016 +0100
MIPS: Fix build error when SMP is used without GIC
[ Upstream commit 588bad2ef32cae7abad24d5ca2f4611a7a7fb2a2 ]
commit 7a50e4688dabb8005df39b2b992d76629b8af8aa upstream.
The MIPS_GIC_IPI should only be selected when MIPS_GIC is also
selected, otherwise it results in a compile error. smp-gic.c uses some
functions from include/linux/irqchip/mips-gic.h like
plat_ipi_call_int_xlate() which are only added to the header file when
MIPS_GIC is set. The Lantiq SoC does not use the GIC, but supports SMP.
The calls top the functions from smp-gic.c are already protected by
some #ifdefs
The first part of this was introduced in commit 72e20142b2bf ("MIPS:
Move GIC IPI functions out of smp-cmp.c")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12774/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 7c196e5a2e90d172ce2bca85bb368f70a016b02c
Author: Markos Chandras <markos.chandras@imgtec.com>
Date: Thu Jul 9 10:40:38 2015 +0100
MIPS: Kconfig: Disable MIPS MT and SMP implementations for R6
[ Upstream commit 5676319c91c8d668635ac0b9b6d9145c4fa418ac ]
R6 does not support the MIPS MT ASE and the CMP/SMP options so
restrict them in order to prevent users from selecting incompatible
SMP configuration for R6 cores. We also disable the CPS/SMP option
because its support hasn't been added to the CPS code yet.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10637/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit e652be4b177954875b8d2d842abfda3626cb1d6a
Author: Markos Chandras <markos.chandras@imgtec.com>
Date: Wed Jul 1 09:31:14 2015 +0100
Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit"
[ Upstream commit 1c885357da2d3cf62132e611c0beaf4cdf607dd9 ]
This reverts commit 6ca716f2e5571d25a3899c6c5c91ff72ea6d6f5e.
SMP/CPS is now supported on 64bit cores.
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10592/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit c839d6e6b096f1c9f2d9be880aedd796095b7a80
Author: James Hogan <james.hogan@imgtec.com>
Date: Tue Mar 8 16:47:53 2016 +0000
ld-version: Fix awk regex compile failure
[ Upstream commit 4b7b1ef2c2f83d702272555e8adb839a50ba0f8e ]
The ld-version.sh script fails on some versions of awk with the
following error, resulting in build failures for MIPS:
awk: scripts/ld-version.sh: line 4: regular expression compile failed (missing '(')
This is due to the regular expression ".*)", meant to strip off the
beginning of the ld version string up to the close bracket, however
brackets have a meaning in regular expressions, so lets escape it so
that awk doesn't expect a corresponding open bracket.
Fixes: ccbef1674a15 ("Kbuild, lto: add ld-version and ld-ifversion ...")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Cc: Michal Marek <mmarek@suse.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kbuild@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 4.4.x-
Patchwork: https://patchwork.linux-mips.org/patch/12838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit c7d4bd1d975e3fa1dd4ecf557ada0e792d551a6c
Author: Ludovic Desroches <ludovic.desroches@atmel.com>
Date: Thu Mar 10 10:17:55 2016 +0100
dmaengine: at_xdmac: fix residue computation
[ Upstream commit 25c5e9626ca4d40928dc9c44f009ce2ed0a739e7 ]
When computing the residue we need two pieces of information: the current
descriptor and the remaining data of the current descriptor. To get
that information, we need to read consecutively two registers but we
can't do it in an atomic way. For that reason, we have to check manually
that current descriptor has not changed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Suggested-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reported-by: David Engraf <david.engraf@sysgo.com>
Tested-by: David Engraf <david.engraf@sysgo.com>
Fixes: e1f7c9eee707 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit eac525506a083a389ba173880979a6291401af2d
Author: Paolo Bonzini <pbonzini@redhat.com>
Date: Tue Mar 8 12:13:39 2016 +0100
KVM: MMU: fix ept=0/pte.u=1/pte.w=0/CR0.WP=0/CR4.SMEP=1/EFER.NX=0 combo
[ Upstream commit 844a5fe219cf472060315971e15cbf97674a3324 ]
Yes, all of these are needed. :) This is admittedly a bit odd, but
kvm-unit-tests access.flat tests this if you run it with "-cpu host"
and of course ept=0.
KVM runs the guest with CR0.WP=1, so it must handle supervisor writes
specially when pte.u=1/pte.w=0/CR0.WP=0. Such writes cause a fault
when U=1 and W=0 in the SPTE, but they must succeed because CR0.WP=0.
When KVM gets the fault, it sets U=0 and W=1 in the shadow PTE and
restarts execution. This will still cause a user write to fault, while
supervisor writes will succeed. User reads will fault spuriously now,
and KVM will then flip U and W again in the SPTE (U=1, W=0). User reads
will be enabled and supervisor writes disabled, going back to the
originary situation where supervisor writes fault spuriously.
When SMEP is in effect, however, U=0 will enable kernel execution of
this page. To avoid this, KVM also sets NX=1 in the shadow PTE together
with U=0. If the guest has not enabled NX, the result is a continuous
stream of page faults due to the NX bit being reserved.
The fix is to force EFER.NX=1 even if the CPU is taking care of the EFER
switch. (All machines with SMEP have the CPU_LOAD_IA32_EFER vm-entry
control, so they do not use user-return notifiers for EFER---if they did,
EFER.NX would be forced to the same value as the host).
There is another bug in the reserved bit check, which I've split to a
separate patch for easier application to stable kernels.
Cc: stable@vger.kernel.org
Cc: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Fixes: f6577a5fa15d82217ca73c74cd2dcbc0f6c781dd
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 09b4fd2014b1ef7d46df8df553f94254ba2a0497
Author: Martin Schwidefsky <schwidefsky@de.ibm.com>
Date: Mon Feb 15 14:46:49 2016 +0100
s390/mm: four page table levels vs. fork
[ Upstream commit 3446c13b268af86391d06611327006b059b8bab1 ]
The fork of a process with four page table levels is broken since
git commit 6252d702c5311ce9 "[S390] dynamic page tables."
All new mm contexts are created with three page table levels and
an asce limit of 4TB. If the parent has four levels dup_mmap will
add vmas to the new context which are outside of the asce limit.
The subsequent call to copy_page_range will walk the three level
page table structure of the new process with non-zero pgd and pud
indexes. This leads to memory clobbers as the pgd_index *and* the
pud_index is added to the mm->pgd pointer without a pgd_deref
in between.
The init_new_context() function is selecting the number of page
table levels for a new context. The function is used by mm_init()
which in turn is called by dup_mm() and mm_alloc(). These two are
used by fork() and exec(). The init_new_context() function can
distinguish the two cases by looking at mm->context.asce_limit,
for fork() the mm struct has been copied and the number of page
table levels may not change. For exec() the mm_alloc() function
set the new mm structure to zero, in this case a three-level page
table is created as the temporary stack space is located at
STACK_TOP_MAX = 4TB.
This fixes CVE-2016-2143.
Reported-by: Marcin Kościelnicki <koriakin@0x04.net>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 1b3ce90bcd25ea9ba08450e605df29e16387a7ca
Author: Steven Rostedt (Red Hat) <rostedt@goodmis.org>
Date: Wed Mar 9 11:58:41 2016 -0500
tracing: Fix check for cpu online when event is disabled
[ Upstream commit dc17147de328a74bbdee67c1bf37d2f1992de756 ]
Commit f37755490fe9b ("tracepoints: Do not trace when cpu is offline") added
a check to make sure that tracepoints only get called when the cpu is
online, as it uses rcu_read_lock_sched() for protection.
Commit 3a630178fd5f3 ("tracing: generate RCU warnings even when tracepoints
are disabled") added lockdep checks (including rcu checks) for events that
are not enabled to catch possible RCU issues that would only be triggered if
a trace event was enabled. Commit f37755490fe9b only stopped the warnings
when the trace event was enabled but did not prevent warnings if the trace
event was called when disabled.
To fix this, the cpu online check is moved to where the condition is added
to the trace event. This will place the cpu online check in all places that
it may be used now and in the future.
Cc: stable@vger.kernel.org # v3.18+
Fixes: f37755490fe9b ("tracepoints: Do not trace when cpu is offline")
Fixes: 3a630178fd5f3 ("tracing: generate RCU warnings even when tracepoints are disabled")
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 3b9f9280aa1321618fc5024314aca23a8716ffd6
Author: Alex Deucher <alexander.deucher@amd.com>
Date: Tue Mar 8 11:31:00 2016 -0500
Revert "drm/radeon/pm: adjust display configuration after powerstate"
[ Upstream commit d74e766e1916d0e09b86e4b5b9d0f819628fd546 ]
This reverts commit 39d4275058baf53e89203407bf3841ff2c74fa32.
This caused a regression on some older hardware.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=113891
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 8fc3813ab4b3a863b44b56013f02d8c955ffd954
Author: Alex Deucher <alexander.deucher@amd.com>
Date: Thu Mar 3 19:26:24 2016 -0500
drm/radeon/dp: add back special handling for NUTMEG
[ Upstream commit c8213a638f65bf487c10593c216525952cca3690 ]
When I fixed the dp rate selection in:
092c96a8ab9d1bd60ada2ed385cc364ce084180e
drm/radeon: fix dp link rate selection (v2)
I accidently dropped the special handling for NUTMEG
DP bridge chips. They require a fixed link rate.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Ken Moffat <zarniwhoop@ntlworld.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit fddbe6c2569a24f097a9973d08a8e282c977ecf3
Author: Alex Deucher <alexander.deucher@amd.com>
Date: Thu Dec 17 10:23:34 2015 -0500
drm/radeon: fix dp link rate selection (v2)
[ Upstream commit 092c96a8ab9d1bd60ada2ed385cc364ce084180e ]
Need to properly handle the max link rate in the dpcd.
This prevents some cases where 5.4 Ghz is selected when
it shouldn't be.
v2: simplify logic, add array bounds check
Reviewed-by: Tom St Denis <tom.stdenis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 7dac6e4062f42f37ef99e86e7f0369ff476af5f6
Author: Alex Deucher <alexander.deucher@amd.com>
Date: Thu May 14 12:47:45 2015 -0400
drm/radeon: make dpcd parameters const
[ Upstream commit 0c3a88407ef2be8bb7c302c298d6ff58ebde4a43 ]
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit eb34a645aee3906baac9cad7defdabf61ac40bfd
Author: Radim KrÄmář <rkrcmar@redhat.com>
Date: Fri Mar 4 15:08:42 2016 +0100
KVM: VMX: disable PEBS before a guest entry
[ Upstream commit 7099e2e1f4d9051f31bbfa5803adf954bb5d76ef ]
Linux guests on Haswell (and also SandyBridge and Broadwell, at least)
would crash if you decided to run a host command that uses PEBS, like
perf record -e 'cpu/mem-stores/pp' -a
This happens because KVM is using VMX MSR switching to disable PEBS, but
SDM [2015-12] 18.4.4.4 Re-configuring PEBS Facilities explains why it
isn't safe:
When software needs to reconfigure PEBS facilities, it should allow a
quiescent period between stopping the prior event counting and setting
up a new PEBS event. The quiescent period is to allow any latent
residual PEBS records to complete its capture at their previously
specified buffer address (provided by IA32_DS_AREA).
There might not be a quiescent period after the MSR switch, so a CPU
ends up using host's MSR_IA32_DS_AREA to access an area in guest's
memory. (Or MSR switching is just buggy on some models.)
The guest can learn something about the host this way:
If the guest doesn't map address pointed by MSR_IA32_DS_AREA, it results
in #PF where we leak host's MSR_IA32_DS_AREA through CR2.
After that, a malicious guest can map and configure memory where
MSR_IA32_DS_AREA is pointing and can therefore get an output from
host's tracing.
This is not a critical leak as the host must initiate with PEBS tracing
and I have not been able to get a record from more than one instruction
before vmentry in vmx_vcpu_run() (that place has most registers already
overwritten with guest's).
We could disable PEBS just few instructions before vmentry, but
disabling it earlier shouldn't affect host tracing too much.
We also don't need to switch MSR_IA32_PEBS_ENABLE on VMENTRY, but that
optimization isn't worth its code, IMO.
(If you are implementing PEBS for guests, be sure to handle the case
where both host and guest enable PEBS, because this patch doesn't.)
Fixes: 26a4f3c08de4 ("perf/x86: disable PEBS on a guest entry.")
Cc: <stable@vger.kernel.org>
Reported-by: Jiřà Olša <jolsa@redhat.com>
Signed-off-by: Radim KrÄmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit c62aadae234ffad0901c20ac1a1aa4e13cce1c20
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Mon Mar 7 23:07:10 2016 -0500
jffs2: reduce the breakage on recovery from halfway failed rename()
[ Upstream commit f93812846f31381d35c04c6c577d724254355e7f ]
d_instantiate(new_dentry, old_inode) is absolutely wrong thing to
do - it will oops if new_dentry used to be positive, for starters.
What we need is d_invalidate() the target and be done with that.
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 906e5a6e6e73316fa4741ca53be014c9477a100c
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Mon Mar 7 22:17:07 2016 -0500
ncpfs: fix a braino in OOM handling in ncp_fill_cache()
[ Upstream commit 803c00123a8012b3a283c0530910653973ef6d8f ]
Failing to allocate an inode for child means that cache for *parent* is
incompletely populated. So it's parent directory inode ('dir') that
needs NCPI_DIR_CACHE flag removed, *not* the child inode ('inode', which
is what we'd failed to allocate in the first place).
Fucked-up-in: commit 5e993e25 ("ncpfs: get rid of d_validate() nonsense")
Fucked-up-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org # v3.19
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 6d44ac3f884b220573b2d46c691127fb6fee0707
Author: Paul Mackerras <paulus@samba.org>
Date: Sat Mar 5 19:34:39 2016 +1100
KVM: PPC: Book3S HV: Sanitize special-purpose register values on guest exit
[ Upstream commit ccec44563b18a0ce90e2d4f332784b3cb25c8e9c ]
Thomas Huth discovered that a guest could cause a hard hang of a
host CPU by setting the Instruction Authority Mask Register (IAMR)
to a suitable value. It turns out that this is because when the
code was added to context-switch the new special-purpose registers
(SPRs) that were added in POWER8, we forgot to add code to ensure
that they were restored to a sane value on guest exit.
This adds code to set those registers where a bad value could
compromise the execution of the host kernel to a suitable neutral
value on guest exit.
Cc: stable@vger.kernel.org # v3.14+
Fixes: b005255e12a3
Reported-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 0d00dbe120f15fd798e7b0e2c69d67da887a9bfb
Author: Mugunthan V N <mugunthanvnm@ti.com>
Date: Mon Mar 7 01:41:22 2016 -0700
ARM: dts: dra7: do not gate cpsw clock due to errata i877
[ Upstream commit 0f514e690740e54815441a87708c3326f8aa8709 ]
Errata id: i877
Description:
------------
The RGMII 1000 Mbps Transmit timing is based on the output clock
(rgmiin_txc) being driven relative to the rising edge of an internal
clock and the output control/data (rgmiin_txctl/txd) being driven relative
to the falling edge of an internal clock source. If the internal clock
source is allowed to be static low (i.e., disabled) for an extended period
of time then when the clock is actually enabled the timing delta between
the rising edge and falling edge can change over the lifetime of the
device. This can result in the device switching characteristics degrading
over time, and eventually failing to meet the Data Manual Delay Time/Skew
specs.
To maintain RGMII 1000 Mbps IO Timings, SW should minimize the
duration that the Ethernet internal clock source is disabled. Note that
the device reset state for the Ethernet clock is "disabled".
Other RGMII modes (10 Mbps, 100Mbps) are not affected
Workaround:
-----------
If the SoC Ethernet interface(s) are used in RGMII mode at 1000 Mbps,
SW should minimize the time the Ethernet internal clock source is disabled
to a maximum of 200 hours in a device life cycle. This is done by enabling
the clock as early as possible in IPL (QNX) or SPL/u-boot (Linux/Android)
by setting the register CM_GMAC_CLKSTCTRL[1:0]CLKTRCTRL = 0x2:SW_WKUP.
So, do not allow to gate the cpsw clocks using ti,no-idle property in
cpsw node assuming 1000 Mbps is being used all the time. If someone does
not need 1000 Mbps and wants to gate clocks to cpsw, this property needs
to be deleted in their respective board files.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit a7029eb2f16ad28aee80f16998bfb1a2f2a787c5
Author: Lokesh Vutla <lokeshvutla@ti.com>
Date: Mon Mar 7 01:41:21 2016 -0700
ARM: OMAP2+: hwmod: Introduce ti,no-idle dt property
[ Upstream commit 6327a31a3f875c438ca13058bc4c73f1a752cd8a ]
commit 2e18f5a1bc18e8af7031b3b26efde25307014837 upstream.
Introduce a dt property, ti,no-idle, that prevents an IP to idle at any
point. This is to handle Errata i877, which tells that GMAC clocks
cannot be disabled.
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 6991aaf3004c32f5e3e856b0bfb0874e122db65d
Author: Peter Ujfalusi <peter.ujfalusi@ti.com>
Date: Thu Nov 12 09:32:58 2015 +0200
ARM: OMAP2+: hwmod: Add hwmod flag for HWMOD_OPT_CLKS_NEEDED
[ Upstream commit c12ba8ce2335389ce5416f88391cd67c7325c963 ]
Some module needs more than one functional clock in order to be accessible,
like the McASPs found in DRA7xx family.
This flag will indicate that the opt_clks need to be handled at the same
time as the main_clk for the given hwmod, ensuring that all needed clocks
are enabled before we try to access the module's address space.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit bde1cccf1a837d6905fe71543c2f4a4e3328dce0
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Sat Mar 5 20:00:12 2016 -0800
target: Drop incorrect ABORT_TASK put for completed commands
[ Upstream commit 7f54ab5ff52fb0b91569bc69c4a6bc5cac1b768d ]
This patch fixes a recent ABORT_TASK regression associated
with commit febe562c, where a left-over target_put_sess_cmd()
would still be called when __target_check_io_state() detected
a command has already been completed, and explicit ABORT must
be avoided.
Note commit febe562c dropped the local kref_get_unless_zero()
check in core_tmr_abort_task(), but did not drop this extra
corresponding target_put_sess_cmd() in the failure path.
So go ahead and drop this now bogus target_put_sess_cmd(),
and avoid this potential use-after-free.
Reported-by: Dan Lane <dracodan@gmail.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 546a8b3c4059af5fd8466f3d1848321e7613904c
Author: Konstantin Khlebnikov <koct9i@gmail.com>
Date: Sun Jan 31 16:21:29 2016 +0300
ovl: copy new uid/gid into overlayfs runtime inode
[ Upstream commit b81de061fa59f17d2730aabb1b84419ef3913810 ]
Overlayfs must update uid/gid after chown, otherwise functions
like inode_owner_or_capable() will check user against stale uid.
Catched by xfstests generic/087, it chowns file and calls utimes.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 091baa9c784fe57b8778a4b754931ffe57245db3
Author: Konstantin Khlebnikov <koct9i@gmail.com>
Date: Sun Jan 31 16:17:53 2016 +0300
ovl: ignore lower entries when checking purity of non-directory entries
[ Upstream commit 45d11738969633ec07ca35d75d486bf2d8918df6 ]
After rename file dentry still holds reference to lower dentry from
previous location. This doesn't matter for data access because data comes
from upper dentry. But this stale lower dentry taints dentry at new
location and turns it into non-pure upper. Such file leaves visible
whiteout entry after remove in directory which shouldn't have whiteouts at
all.
Overlayfs already tracks pureness of file location in oe->opaque. This
patch just uses that for detecting actual path type.
Comment from Vivek Goyal's patch:
Here are the details of the problem. Do following.
$ mkdir upper lower work merged upper/dir/
$ touch lower/test
$ sudo mount -t overlay overlay -olowerdir=lower,upperdir=upper,workdir=
work merged
$ mv merged/test merged/dir/
$ rm merged/dir/test
$ ls -l merged/dir/
/usr/bin/ls: cannot access merged/dir/test: No such file or directory
total 0
c????????? ? ? ? ? ? test
Basic problem seems to be that once a file has been unlinked, a whiteout
has been left behind which was not needed and hence it becomes visible.
Whiteout is visible because parent dir is of not type MERGE, hence
od->is_real is set during ovl_dir_open(). And that means ovl_iterate()
passes on iterate handling directly to underlying fs. Underlying fs does
not know/filter whiteouts so it becomes visible to user.
Why did we leave a whiteout to begin with when we should not have.
ovl_do_remove() checks for OVL_TYPE_PURE_UPPER() and does not leave
whiteout if file is pure upper. In this case file is not found to be pure
upper hence whiteout is left.
So why file was not PURE_UPPER in this case? I think because dentry is
still carrying some leftover state which was valid before rename. For
example, od->numlower was set to 1 as it was a lower file. After rename,
this state is not valid anymore as there is no such file in lower.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Reported-by: Viktor Stanchev <me@viktorstanchev.com>
Suggested-by: Vivek Goyal <vgoyal@redhat.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=109611
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit e786702fff38e2b5142029d6de615abf1c8e436f
Author: Rui Wang <rui.y.wang@intel.com>
Date: Fri Jan 8 23:09:59 2016 +0800
ovl: fix getcwd() failure after unsuccessful rmdir
[ Upstream commit ce9113bbcbf45a57c082d6603b9a9f342be3ef74 ]
ovl_remove_upper() should do d_drop() only after it successfully
removes the dir, otherwise a subsequent getcwd() system call will
fail, breaking userspace programs.
This is to fix: https://bugzilla.kernel.org/show_bug.cgi?id=110491
Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Reviewed-by: Konstantin Khlebnikov <koct9i@gmail.com>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 7ce08a0c9992da8986b06154a768646e41012469
Author: Jouni Malinen <jouni@qca.qualcomm.com>
Date: Tue Mar 1 00:29:00 2016 +0200
mac80211: Fix Public Action frame RX in AP mode
[ Upstream commit 1ec7bae8bec9b72e347e01330c745ab5cdd66f0e ]
Public Action frames use special rules for how the BSSID field (Address
3) is set. A wildcard BSSID is used in cases where the transmitter and
recipient are not members of the same BSS. As such, we need to accept
Public Action frames with wildcard BSSID.
Commit db8e17324553 ("mac80211: ignore frames between TDLS peers when
operating as AP") added a rule that drops Action frames to TDLS-peers
based on an Action frame having different DA (Address 1) and BSSID
(Address 3) values. This is not correct since it misses the possibility
of BSSID being a wildcard BSSID in which case the Address 1 would not
necessarily match.
Fix this by allowing mac80211 to accept wildcard BSSID in an Action
frame when in AP mode.
Fixes: db8e17324553 ("mac80211: ignore frames between TDLS peers when operating as AP")
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 87e0016ccb1f9cbe377d4af19cb840acbbdff206
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri Feb 26 22:13:40 2016 +0100
mac80211: check PN correctly for GCMP-encrypted fragmented MPDUs
[ Upstream commit 9acc54beb474c81148e2946603d141cf8716b19f ]
Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:
The receiver shall discard MSDUs and MMPDUs whose constituent
MPDU PN values are not incrementing in steps of 1.
Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit a60ebc3d637071d56b66aac189dd3fcdfa707704
Author: Takashi Iwai <tiwai@suse.de>
Date: Mon Feb 29 18:01:18 2016 +0100
ASoC: wm_adsp: Fix enum ctl accesses in a wrong type
[ Upstream commit 15c665700bf6f4543f003ac0fbb1e9ec692e93f2 ]
The firmware ctls like "DSP1 Firmware" in wm_adsp codec driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit f4d57e47121afdfad04a82cbd07b246873ec1e19
Author: Takashi Iwai <tiwai@suse.de>
Date: Mon Feb 29 18:01:15 2016 +0100
ASoC: wm8994: Fix enum ctl accesses in a wrong type
[ Upstream commit 8019c0b37cd5a87107808300a496388b777225bf ]
The DRC Mode like "AIF1DRC1 Mode" and EQ Mode like "AIF1.1 EQ Mode" in
wm8994 codec driver are enum ctls, while the current driver accesses
wrongly via value.integer.value[]. They have to be via
value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 58de29e6c58f7830826f48d7b0454cc1cec630ca
Author: Takashi Iwai <tiwai@suse.de>
Date: Mon Feb 29 18:01:12 2016 +0100
ASoC: wm8958: Fix enum ctl accesses in a wrong type
[ Upstream commit d0784829ae3b0beeb69b476f017d5c8a2eb95198 ]
"MBC Mode", "VSS Mode", "VSS HPF Mode" and "Enhanced EQ Mode" ctls in
wm8958 codec driver are enum, while the current driver accesses
wrongly via value.integer.value[]. They have to be via
value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 33824bb3cb275aa931c996c2f67bf8bf9babe301
Author: Takashi Iwai <tiwai@suse.de>
Date: Mon Feb 29 17:20:48 2016 +0100
ASoC: dapm: Fix ctl value accesses in a wrong type
[ Upstream commit 741338f99f16dc24d2d01ac777b0798ae9d10a90 ]
snd_soc_dapm_dai_link_get() and _put() access the associated ctl
values as value.integer.value[]. However, this is an enum ctl, and it
has to be accessed via value.enumerated.item[]. The former is long
while the latter is unsigned int, so they don't align.
Fixes: c66150824b8a ('ASoC: dapm: add code to configure dai link parameters')
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 01ff3a0a01366a231593476cfe775596ebdba30f
Author: Maximilain Schneider <max@schneidersoft.net>
Date: Tue Feb 23 01:17:28 2016 +0000
can: gs_usb: fixed disconnect bug by removing erroneous use of kfree()
[ Upstream commit e9a2d81b1761093386a0bb8a4f51642ac785ef63 ]
gs_destroy_candev() erroneously calls kfree() on a struct gs_can *, which is
allocated through alloc_candev() and should instead be freed using
free_candev() alone.
The inappropriate use of kfree() causes the kernel to hang when
gs_destroy_candev() is called.
Only the struct gs_usb * which is allocated through kzalloc() should be freed
using kfree() when the device is disconnected.
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 870be7d2ade42485fa40ac3d2ac8bcffa3afc957
Author: Felix Fietkau <nbd@openwrt.org>
Date: Thu Feb 18 19:49:18 2016 +0100
mac80211: minstrel_ht: set default tx aggregation timeout to 0
[ Upstream commit 7a36b930e6ed4702c866dc74a5ad07318a57c688 ]
The value 5000 was put here with the addition of the timeout field to
ieee80211_start_tx_ba_session. It was originally added in mac80211 to
save resources for drivers like iwlwifi, which only supports a limited
number of concurrent aggregation sessions.
Since iwlwifi does not use minstrel_ht and other drivers don't need
this, 0 is a better default - especially since there have been
recent reports of aggregation setup related issues reproduced with
ath9k. This should improve stability without causing any adverse
effects.
Cc: stable@vger.kernel.org
Acked-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit ea46df70efaa589117dce85dec3e3707362e514a
Author: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Date: Thu Feb 18 15:47:13 2016 +0000
ASoC: samsung: Use IRQ safe spin lock calls
[ Upstream commit 316fa9e09ad76e095b9d7e9350c628b918370a22 ]
Lockdep warns of a potential lock inversion, i2s->lock is held numerous
times whilst we are under the substream lock (snd_pcm_stream_lock). If
we use the IRQ unsafe spin lock calls, you can also end up locking
snd_pcm_stream_lock whilst under i2s->lock (if an IRQ happens whilst we
are holding i2s->lock). This could result in deadlock.
[ 18.147001] CPU0 CPU1
[ 18.151509] ---- ----
[ 18.156022] lock(&(&pri_dai->spinlock)->rlock);
[ 18.160701] local_irq_disable();
[ 18.166622] lock(&(&substream->self_group.lock)->rlock);
[ 18.174595] lock(&(&pri_dai->spinlock)->rlock);
[ 18.181806] <Interrupt>
[ 18.184408] lock(&(&substream->self_group.lock)->rlock);
[ 18.190045]
[ 18.190045] *** DEADLOCK ***
This patch changes to using the irq safe spinlock calls, to avoid this
issue.
Fixes: ce8bcdbb61d9 ("ASoC: samsung: i2s: Protect more registers with a spinlock")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 7e62b968351c3759db1ad78b4aaaeff72ab2b998
Author: Liad Kaufman <liad.kaufman@intel.com>
Date: Sun Feb 14 15:32:58 2016 +0200
iwlwifi: mvm: inc pending frames counter also when txing non-sta
[ Upstream commit fb896c44f88a75843a072cd6961b1615732f7811 ]
Until this patch, when TXing non-sta the pending_frames counter
wasn't increased, but it WAS decreased in
iwl_mvm_rx_tx_cmd_single(), what makes it negative in certain
conditions. This in turn caused much trouble when we need to
remove the station since we won't be waiting forever until
pending_frames gets 0. In certain cases, we were exhausting
the station table even in BSS mode, because we had a lot of
stale stations.
Increase the counter also in iwl_mvm_tx_skb_non_sta() after a
successful TX to avoid this outcome.
CC: <stable@vger.kernel.org> [3.18+]
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 60ca0012a0965fe57712eef8361ec99b9c76eb06
Author: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Date: Tue Feb 2 08:12:26 2016 +0100
mac80211: minstrel: Change expected throughput unit back to Kbps
[ Upstream commit 212c5a5e6ba61678be6b5fee576e38bccb50b613 ]
The change from cur_tp to the function
minstrel_get_tp_avg/minstrel_ht_get_tp_avg changed the unit used for the
current throughput. For example in minstrel_ht the correct
conversion between them would be:
mrs->cur_tp / 10 == minstrel_ht_get_tp_avg(..).
This factor 10 must also be included in the calculation of
minstrel_get_expected_throughput and minstrel_ht_get_expected_throughput to
return values with the unit [Kbps] instead of [10Kbps]. Otherwise routing
algorithms like B.A.T.M.A.N. V will make incorrect decision based on these
values. Its kernel based implementation expects expected_throughput always
to have the unit [Kbps] and not sometimes [10Kbps] and sometimes [Kbps].
The same requirement has iw or olsrdv2's nl80211 based statistics module
which retrieve the same data via NL80211_STA_INFO_TX_BITRATE.
Cc: stable@vger.kernel.org
Fixes: 6a27b2c40b48 ("mac80211: restructure per-rate throughput calculation into function")
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit d5bb89facc7b689292d85471be1fdbae1928e224
Author: Chris Bainbridge <chris.bainbridge@gmail.com>
Date: Wed Jan 27 15:46:18 2016 +0000
mac80211: fix use of uninitialised values in RX aggregation
[ Upstream commit f39ea2690bd61efec97622c48323f40ed6e16317 ]
Use kzalloc instead of kmalloc for struct tid_ampdu_rx to
initialize the "removed" field (all others are initialized
manually). That fixes:
UBSAN: Undefined behaviour in net/mac80211/rx.c:932:29
load of value 2 is not a valid value for type '_Bool'
CPU: 3 PID: 1134 Comm: kworker/u16:7 Not tainted 4.5.0-rc1+ #265
Workqueue: phy0 rt2x00usb_work_rxdone
0000000000000004 ffff880254a7ba50 ffffffff8181d866 0000000000000007
ffff880254a7ba78 ffff880254a7ba68 ffffffff8188422d ffffffff8379b500
ffff880254a7bab8 ffffffff81884747 0000000000000202 0000000348620032
Call Trace:
[<ffffffff8181d866>] dump_stack+0x45/0x5f
[<ffffffff8188422d>] ubsan_epilogue+0xd/0x40
[<ffffffff81884747>] __ubsan_handle_load_invalid_value+0x67/0x70
[<ffffffff82227b4d>] ieee80211_sta_reorder_release.isra.16+0x5ed/0x730
[<ffffffff8222ca14>] ieee80211_prepare_and_rx_handle+0xd04/0x1c00
[<ffffffff8222db03>] __ieee80211_rx_handle_packet+0x1f3/0x750
[<ffffffff8222e4a7>] ieee80211_rx_napi+0x447/0x990
While at it, convert to use sizeof(*tid_agg_rx) instead.
Fixes: 788211d81bfdf ("mac80211: fix RX A-MPDU session reorder timer deletion")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
[reword commit message, use sizeof(*tid_agg_rx)]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 6d5202f35ff2277d76eb53da93ed70080d6f4ec1
Author: Johannes Berg <johannes.berg@intel.com>
Date: Wed Jan 27 13:29:34 2016 +0100
cfg80211/wext: fix message ordering
[ Upstream commit cb150b9d23be6ee7f3a0fff29784f1c5b5ac514d ]
Since cfg80211 frequently takes actions from its netdev notifier
call, wireless extensions messages could still be ordered badly
since the wext netdev notifier, since wext is built into the
kernel, runs before the cfg80211 netdev notifier. For example,
the following can happen:
5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default
link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST,UP>
link/ether
when setting the interface down causes the wext message.
To also fix this, export the wireless_nlevent_flush() function
and also call it from the cfg80211 notifier.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 746ba2ee59997437988060c709324057b761bd96
Author: Johannes Berg <johannes.berg@intel.com>
Date: Wed Jan 27 12:37:52 2016 +0100
wext: fix message delay/ordering
[ Upstream commit 8bf862739a7786ae72409220914df960a0aa80d8 ]
Beniamino reported that he was getting an RTM_NEWLINK message for a
given interface, after the RTM_DELLINK for it. It turns out that the
message is a wireless extensions message, which was sent because the
interface had been connected and disconnection while it was deleted
caused a wext message.
For its netlink messages, wext uses RTM_NEWLINK, but the message is
without all the regular rtnetlink attributes, so "ip monitor link"
prints just rudimentary information:
5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default
link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
Deleted 5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default
link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST,UP>
link/ether
(from my hwsim reproduction)
This can cause userspace to get confused since it doesn't expect an
RTM_NEWLINK message after RTM_DELLINK.
The reason for this is that wext schedules a worker to send out the
messages, and the scheduling delay can cause the messages to get out
to userspace in different order.
To fix this, have wext register a netdevice notifier and flush out
any pending messages when netdevice state changes. This fixes any
ordering whenever the original message wasn't sent by a notifier
itself.
Cc: stable@vger.kernel.org
Reported-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>